Temperature- and frequency-dependent hysteresis scaling behaviour and phase transitions in a [001]c 0.73Pb(Mg1/3Nb2/3)O3-0.27PbTiO3 single crystal

The dielectric properties and bipolar polarization-electric field (P-E) and strain-electric field (S-E) dynamic hysteresis of a relaxor [001]_c 0.73Pb(Mg_1/3Nb_2/3)O₃-0.27PbTiO₃ (PMN-0.27PT) single crystal were investigated to reveal more details of the temperature-induced phase transitions. Different linear scaling relations for ferroelectric hysteresis area <A>, coercive field E_c, saturation polarization P_s and remnant polarization P_r versus temperature τ were measured in different temperature regions. For each measurement frequency f, all hysteresis parameters were found to decrease linearly with temperature in the temperature range of the single rhombohedral (R) phase or tetragonal (T) phase, and the rate of decrease in the T phase was observed to be much larger than the corresponding rate in the R phase. In the temperature range near the R-T phase transition, the exponent α in the power law <A>∝f ^α for the R phase was found to be smaller than that for the T phase, and the magnitude of α depended strongly on temperature when the crystal was in the R-T coexisting phase state. Our experimental and theoretical results indicate that the difference in the activation energy and dipole moment in the R and T phases may lead to the observed discrepancy for the P-E and S-E hysteresis behaviour in different temperature regions.     

Theoretical investigations on the spin Hamiltonian parameters for Er3+ ion in LiYF4

The spin Hamiltonian parameters g_∥, g_⊥, A_∥ and A_⊥ for Er³⁺ ion in LiYF₄ are investigated by using the perturbation formulas of these parameters for a 4f¹¹ ion in tetragonal symmetry. In these formulas, the contributions to the spin Hamiltonian parameters from the second-order perturbation terms and the admixtures of different states are considered. The relevant crystal field parameters are calculated from the superposition model and the local structural parameters of the Y³⁺ site occupied by impurity Er³⁺. The theoretical optical spectra within ⁴I_15/2 and ⁴I_13/2 states and the spin Hamiltonian parameters obtained in this work are consistent with the observed values.     

Effect of Magnetic Interaction on Thermally Activated Reversal in a Magnet With a Distribution of Energy Barriers

The time dependence of magnetization is usually expressed as M(t)=M₀-SInt [see Proc. Phys. Soc. 62, 562 (1949)] for magnetic viscosity experiments. Considering magnetic interaction during the thermal activation process, a form as M(t)=M₀-SIn(t+t₀) is deduced. The dipolar interaction and exchange coupling in a magnet can lead to positive and nonpositive t₀, respectively. In the experiments of the magnetic viscosity for nanocrystalline Pr₂Fe₁₄B ribbons, the existence of positive t₀ is confirmed.     

Internal relative humidity distribution in high-performance cement paste due to moisture diffusion and self-desiccation

This investigation was carried out to study internal relative humidity (IRH) distribution of cement paste made with different water / cement ratios (w / c) and mineral admixtures in isothermal drying conditions. IRH changes in cement paste resulting from self-desiccation and moisture diffusion, respectively, at different ages were studied. The change laws of IRH in cement paste resulting from combining moisture diffusion with self-desiccation were discussed. The results indicate that IRH reduction of cement paste with w / c higher than 0.4 is mainly affected by moisture diffusion. However, IRH reduction of cement paste with w / c no higher than 0.4 is controlled by both moisture diffusion and self-desiccation. With the decrease of w / c, IRH reduction of cement paste resulting from self-desiccation increases, and IRH reduction resulting from moisture diffusion decreases at a given age. IRH decrement of cement paste incorporated with silica fume and ground blast-furnace slag is higher than that of control paste. w / c and the distance to the exposed surface play a significant role in IRH change resulting from moisture diffusion in isothermal drying condition. Change laws of IRH in cement paste with silica fume due to moisture diffusion considering self-desiccation are different from those in cement paste without silica fume.     

Mechanical properties of hybrid fiber-reinforced concrete at low fiber volume fraction

Concretes containing different types of hybrid fibers at the same volume fraction (0.5%) were compared in terms of compressive, splitting tensile, and flexural properties. Three types of hybrid composites were constructed using fiber combinations of polypropylene (PP) and carbon, carbon and steel, and steel and PP fibers. Test results showed that the fibers, when used in a hybrid form, could result in superior composite performance compared to their individual fiber-reinforced concretes. Among the three types of hybrids, the carbon-steel combination gave concrete of the highest strength and flexural toughness because of the similar modulus and the synergistic interaction between the two reinforcing fibers.     

热处理条件对硅酸盐玻璃中原位形成银纳米颗粒的影响

用离子交换结合热处理法制备银(Ag)纳米颗粒-玻璃复合材料.用透射电镜、高分辨透射电子显微镜、Ruthefford背散射谱和紫外-可见光吸收光谱研究了热处理条件对玻璃中原位形成Ag纳米颗粒的影响.结果显示:随着热处理温度升高,玻璃表面的Ag原子逐渐向玻璃内部扩散,其表面摩尔浓度逐渐降低.提高热处理温度和延长热处理时间都有利于提高玻璃中Ag纳米颗粒的体积分数.空气中,高温热处理高掺Ag量的白玻璃样品时发生二次成核,因此,Ag纳米颗粒尺寸呈双峰分布.Ag纳米颗粒尺寸的双峰分布导致其等离子体共振吸收峰出现双峰.在氢气气氛中,在250℃热处理2min,即可在玻璃中形成大量Ag纳米颗粒,颗粒尺寸小于空气中高温热处理样品的尺寸,从而引起表面等离子体共振吸收峰发生蓝移.     

Synthesis of water-soluble single-walled carbon nanotubes by RAFT polymerization

Water-soluble single-walled carbon nanotubes (SWNTs) were synthesized by grafting poly(acrylamide) (PAM) from the surface of SWNT via reversible addition-fragmentation chain transfer (RAFT) polymerization. The RAFT agents were covalently attached to the SWNTs by functionalizing SWNTs with in situ generated diazonium compounds. The product was characterized by means of FT-IR, Raman, ¹H NMR, TGA and TEM. The results showed that PAM chains had successfully grafted from SWNT by RAFT polymerization. The amount of PAM grown from SWNT increased with the polymerization time. The acrylamide conversion increased linearly with the polymerization time, indicating the “living” characteristics of the RAFT polymerization. TEM was utilized to image PAM-g-SWNT, showing relatively uniform polymer coatings present on the surface of individual, debundled nanotubes.     

Influence of polymer on cement hydration in SBR-modified cement pastes

The influence of styrene-butadiene rubber (SBR) latex on cement hydrates Ca(OH)₂, ettringite, C₄AH₁₃ and C-S-H gel and the degree of cement hydration is studied by means of several measure methods. The results of DSC and XRD show that the Ca(OH)₂ content in wet-cured SBR-modified cement pastes increases with polymer-cement ratio (P/C) and reaches a maximum when P/C is 5%, 10% and 10% for the pastes hydrated for 3 d, 7 d and 28 d, respectively. With wet cure, appropriate addition of SBR promotes the hydration of cement, while the effect of SBR on the content of Ca(OH)₂ and the degree of cement hydration is not remarkable in mixed-cured SBR-modified cement pastes. XRD results illustrate that SBR accelerates the reaction of calcium aluminate with gypsum, and thus enhances the formation and stability of the ettringite and inhibits the formation of C₄AH₁₃. The structure of aluminum-oxide and silicon-oxide polyhedron is characterized by ²⁷Al and ²⁹Si solid state NMR spectrum method, which shows that tetrahedron and octahedron are the main forms of aluminum-oxide polyhedrons in SBR-modified cement pastes. There are only [SiO₄]⁴⁻ tetrahedron monomer and dimer in the modified pastes hydrated for 3 d, but there appears three-tetrahedron polymer in the modified pastes hydrated for 28 d. The effect of low SBR dosage on the structure of aluminum-oxide and silicon-oxide polyhedron is slight. However, the combination of Al³⁺ with [SiO₄]⁴⁻ is restrained when P/C is above 15%, and the structure of Al³⁺ is changed obviously. Meantime, the polymerization of the [SiO₄]⁴⁻ tetrahedron in C-S-H gel is controlled.