网络展开图与符号网络分析

采用封闭网络模型,按照电路元件参数,采用开路、短路和着色运算,将电路图逐层分解,得到网络展开图.给出网络展开图的概念和运算规则,指出网络展开图中从根到末稍每个路径的值就是网络行列式展开式中的一个有效项,从而由网络展开图得到符号网络函数.该方法直接对电路图进行运算,不需要建立任何形式的电路方程和行列式,适用于一般的有源电路,而且能生成各种类型的网络函数.     

Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

Preparation of BaMgAl10O17∶Eu2+ and Its Phase Behavior in Microemulsion System

BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra.     

Ready, Set, Go! The Voronoi diagram of moving points that start from a line

It is an outstanding open problem of computational geometry to prove a near-quadratic upper bound on the number of combinatorial changes in the Voronoi diagram of points moving at a common constant speed along linear trajectories in the plane. In this note we observe that this quantity is Θ(n²) if the points start their movement from a common line.     

红外隐身技术的现状与发展

综述了红外隐身技术的现状，指明了存在的问题以及发展的方向。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

Prediction of liquid–liquid phase diagrams of aqueous salt+PEG systems using a thermodynamic model

In this study a thermodynamic model for the phase behavior of aqueous salt+polymer solutions is developed. The model is based on the solution theory of Hill, which included scaling laws for the polymer molecular mass dependence and Pitzer–Debye–Hückel theory. This model was tested for systems composed of two different molecular mass of polyethylene glycols (PEG) and five different inorganic salts. All the model parameters were determined from independent measurements. The agreement between the experimental and predicted phase diagrams by this model is good.     

热力学相图计算技术在闪速燃烧合成氮化硅铁中的应用

将热力学相图计算技术应用于Si-Fe-O-N体系,以评估由FeSi75粉闪速燃烧合成氮化硅铁的条件和目标产物。结果表明:将闪速燃烧温度控制在1200～1500℃之间较为适宜,此时平衡态产物中除主要含有Si3N4以外,还有一定量的Fe与Si间化合物和少量稳定的SiO2存在。此计算结果与实际试验结果吻合良好。     

Polygonal extrusion

A sweeping operation called polygonal extrusion is defined to improve the modeling power of CSG-based modeling. It is assumed that a 2D cross-sectional polygon (sweeping polygon) moves in space while its containing plane is kept orthogonal to the tangent direction of the trajectory curve, a planar polygonal chain having no self-intersections. The objective of the paper is to compute the boundary of the swept volume of the sweeping polygon as a set of polygons (or triangles). The most significant challenge to accomplishing this objective is the problem of trimming the swept volume. To solve the trimming problem, 2D-curve offsetting methods are employed. Two algorithms are presented for polygonal extrusion that are based on different offsetting methods, the Voronoi diagram and PWID offset. The proposed algorithms have been implemented and tested with various examples. Published online: 28 January 2003