Mixing characteristics for the single and air-water two-phase flows in miniaturized parallel multichannel-based devices

Investigation on the miniaturized parallel multichannel-based devices packed with glass beads to improve the mass exchange execution is the critical focal point of the current study. One of the essential parameters to specify the miniaturized devices' flow distribution is the residence time distribution (RTD). In the present context, the RTDs of a liquid tracer were investigated for the air-water multiphase flows (concurrent) across the multichannel-based miniaturized devices (comprising of 11 similar dimensional parallel channels). The devices were variable in height and packed with glass beads. The conductivity estimations generated the RTD curves and were addressed by the axial dispersion model (ADM). The fluid-flow rates differed within the range of 5–23 ml min⁻¹. The axial dispersion coefficients and the rate of the specific energy dispersion were investigated. The effects of pressure difference and geometry on the hydrodynamic attributes and mixing properties were well-illustrated, and the new correlations were suggested.     

Comparative analysis of inbreeding parameters and runs of homozygosity islands in 2 Italian autochthonous cattle breeds mainly raised in the Parmigiano-Reggiano cheese production region

Reggiana and Modenese are autochthonous cattle breeds, reared in the North of Italy, that can be mainly distinguished for their standard coat color (Reggiana is red, whereas Modenese is white with some pale gray shades). Almost all milk produced by these breeds is transformed into 2 mono-breed branded Parmigiano-Reggiano cheeses, from which farmers receive the economic incomes needed for the sustainable conservation of these animal genetic resources. After the setting up of their herd books in 1960s, these breeds experienced a strong reduction in the population size that was subsequently reverted starting in the 1990s (Reggiana) or more recently (Modenese) reaching at present a total of about 2,800 and 500 registered cows, respectively. Due to the small population size of these breeds, inbreeding is a very important cause of concern for their conservation programs. Inbreeding is traditionally estimated using pedigree data, which are summarized in an inbreeding coefficient calculated at the individual level (F_PED). However, incompleteness of pedigree information and registration errors can affect the effectiveness of conservation strategies. High-throughput SNP genotyping platforms allow investigation of inbreeding using genome information that can overcome the limits of pedigree data. Several approaches have been proposed to estimate genomic inbreeding, with the use of runs of homozygosity (ROH) considered to be the more appropriate. In this study, several pedigree and genomic inbreeding parameters, calculated using the whole herd book populations or considering genotyping information (GeneSeek GGP Bovine 150K) from 1,684 Reggiana cattle and 323 Modenese cattle, were compared. Average inbreeding values per year were used to calculate effective population size. Reggiana breed had generally lower genomic inbreeding values than Modenese breed. The low correlation between pedigree-based and genomic-based parameters (ranging from 0.187 to 0.195 and 0.319 to 0.323 in the Reggiana and Modenese breeds, respectively) reflected the common problems of local populations in which pedigree records are not complete. The high proportion of short ROH over the total number of ROH indicates no major recent inbreeding events in both breeds. ROH islands spread over the genome of the 2 breeds (15 in Reggiana and 14 in Modenese) identified several signatures of selection. Some of these included genes affecting milk production traits, stature, body conformation traits (with a main ROH island in both breeds on BTA6 containing the ABCG2, NCAPG, and LCORL genes) and coat color (on BTA13 in Modenese containing the ASIP gene). In conclusion, this work provides an extensive comparative analysis of pedigree and genomic inbreeding parameters and relevant genomic information that will be useful in the conservation strategies of these 2 iconic local cattle breeds.     

Determinants of the intention to use non-medical insertable digital devices: The case of Chile and Colombia

In the past, thinking of carrying electronic devices inside our bodies was only posed by non-real scenarios. The emergence of insertable devices has changed this. Since this technology is still in its initial development stages, few studies have investigated factors that influence its acceptance. This paper analyzes the predictors of the intention to use non-medical insertable devices in two Latin American contexts. We used partial least squares structural equation modeling to examine whether six constructs predicted intention to use insertable devices. A questionnaire was administered to undergraduate students located in Colombia and Chile (n = 672). We also examined whether these predictors influenced intention differently for both of them. Four common constructs significantly and positively influenced both Chilean and Colombian respondents to use insertable devices (hedonic motivation, habit, performance expectancy, and social influence). Also, the habit has a complementary mediating effect on the relationship between social influence and behavioral intention. By contrast, effort expectations were a positive and significant predictor, but only among Chilean respondents. Findings suggest that when technologies are emerging, well-known predictors of intention (e.g., performance and effort expectations) are less influential than predictors related to self-efficacy (e.g., habit and hedonic motivation). The use of insertable devices has a significant impact on society. Thus, a better understanding of what motivates their use has implications for both academia and industry.     

Trade-off study between risk and benefit in safety devices for hydrogen refueling stations using a dynamic physical model

As hydrogen refueling stations become increasingly common, it is clear that a high level of economic efficiency and safety is crucial to promoting their use. One way to reduce costs is to use a simple orifice instead of an excess flow valve, which Japanese safety regulations have identified as a safety device. However, there is concern about its effect on refueling time and on risk due to hydrogen leakage. To clarify the effect, we did a study of model-based refueling time evaluation and quantitative risk assessment for a typical refueling station. This study showed that an orifice is an effective alternative safety device. The increase in refueling time was less than 10%, based on simulations using a dynamic physical model of the station. Neither was there a significant difference in the risk between a configuration with excess flow valves and one with an orifice.     

无线电综合测试仪校准装置的研究及其不确定度分析

This calibration device of radio comprehensive tester is studied and established in this paper. It solves the verification and calibration of a large number of general-purpose radio comprehensive testers. The calibration device consists of four calibration sub- systems and calibration software system, including RF generator, audio generator, audio analyzer and RF analyzer. It also researches on the configuration of standard equipment and analyzes the uncertainty of the calibration devices, ensuring accurate and reliable val- ue transfer.     

Long-run urban dynamics: understanding local housing market change in London

Abstract

Recently, a literature has emerged using empirical techniques to study the evolution of international cities over many centuries; however, few studies examine long-run change within cities. Conventional models and concepts are not always appropriate and data issues make long-run neighbourhood analysis particularly problematic. This paper addresses some of these points. First, it discusses why the analysis of long-run urban change is important for modern urban policy and considers the most important concepts. Second, it constructs a novel data set at the micro level, which allows consistent comparisons of London neighbourhoods in 1881 and 2001. Third, the paper models some of the key factors that affected long-run change, including the role of housing. There is evidence that the relative social positions of local urban areas persist over time but, nevertheless, at fine spatial scales, local areas still exhibit change, arising from aggregate population dynamics, from advances in technology, and also from the effects of shocks, such as wars. In general, where small areas are considered, long-run changes are likely to be greater, because individuals are more mobile over short than long distances. Finally, the paper considers the implications for policy.     

Effect of the thicknesses of the Al2SiO5 ion conductor on the opto-electrical properties for all-solid electrochromic devices

In this study, an all-solid-state electrochromic device (ECD) with the structure of ITO/WO₃/Al₂SiO₅/NiO_x/ITO was prepared, and the effect of the Al₂SiO₅ solid electrolyte thicknesses on the opto-electrical performance was investigated. The microstructure and surface morphology were characterized using XRD, SEM and AFM, and the surface morphology and degree of surface looseness demonstrate a significant influence on the opto-electrical properties of ECDs. The charge transfer dynamics at the solid-solid interface were characterized using EIS to obtain an ionic conductivity of 4.637 × 10^-8 S/cm. CV, CA and UV–Visible spectra were employed to record the in situ electrochemical and optical properties. The results revealed that the highest optical modulation was 44.58%, the coloring and bleaching times were 14.8 s and 3.7 s, and the highest coloring efficiency was 98.17 cm²/C, which indicates that excellent opto-electrical properties were obtained. When the thickness increases, the degree of surface dense morphology transforms, and the loose morphology is more favorable for ion conductivity, which improves the opto-electrical properties. The results in this study provide insights into the understanding of Al³⁺-based all-solid-state ECDs, which promote the exploration of new types of Al³⁺ ionic conductors for all-solid-state ECDs.     

Evolution of Local Structural Ordering and Chemical Distribution upon Delithiation of a Rock Salt–Structured Li1.3Ta0.3Mn0.4O2 Cathode

Lithium‐rich disordered rock‐salt oxides have attracted great interest owing to their promising performance as Li‐ion battery cathodes. While experimental and theoretical efforts are critical in advancing this class of materials, a fundamental understanding of key property changes upon Li extraction is largely missing. In the present study, single‐crystal synthesis of a new disordered rock‐salt cathode material, Li_1.3Ta_0.3Mn_0.4O₂ (LTMO), and its use as a model compound to investigate Li concentration–driven evolution of local cationic ordering, charge compensation, and chemical distribution are reported. Through the combined use of 2D and 3D X‐ray nanotomography, it is shown that Li removal accompanied by oxygen oxidation is correlated with the development of morphological defects such as particle cracking. Chemical heterogeneity, quantified by subparticle level distribution of Mn valence state, is minimal during Mn redox, which drastically increases upon the formation of cracks during oxygen redox. Density functional theory and bond valence sum mismatch calculations reveal the presence of local short‐range ordering in the pristine oxide, which gradually disappears along with the extraction of Li. The study suggests that with cycling the transformation into true cation–disordered state can be expected, which likely impacts the voltage profile and obtainable energy density of the oxide cathodes.     

On one boundary problem for nonlinear stationary controlled system

The object of study is nonlinear stationary controlled system of ordinary differential equations with constant disturbance in the right part. The problem of constructing the synthesising control function providing the transfer of this system from the initial state to the origin is considered. The sufficiently simple for numerical implementation algorithm of solution of the above-mentioned problem is obtained. It is shown that for local null controllability of the considered system, it is sufficient that the conditions of the Kalman's type were satisfied. In addition, the estimates restricting the choice of initial conditions and external disturbances under which the transfer is guaranteed are obtained. The main idea of the method of construction of the desired control function consists in reducing the original problem to stabilisation of a special kind linear non-stationary system and solving the Cauchy problem for an auxiliary system of ordinary differential equations closed by stabilising control. The simplicity of the realisation of this algorithm is determined by the construction of the auxiliary system and its stabilisation that could be obtained by analytical methods. The effectiveness of the method is illustrated by solving the problem of crane control and its numerical simulation.