Unique CNTs-chained Li4Ti5O12 nanoparticles as excellent high rate anode materials for Li-ion capacitors

Composite anode materials with a unique architecture of carbon nanotubes (CNTs)-chained spinel lithium titanate (Li₄Ti₅O₁₂, LTO) nanoparticles are prepared for lithium ion capacitors (LICs). The CNTs networks derived from commercial conductive slurry not only bring out a steric hindrance effect to restrict the growth of Li₄Ti₅O₁₂ particles but greatly enhance the electronic conductivity of the CNTs/LTO composites, both have contributed to the excellent rate capability and cycle stability. The capacity retention at 30 C (1 C = 175 mA g^?1) is as high as 89.7% of that at 0.2 C with a CNTs content of 11 wt%. Meanwhile, there is not any capacity degradation after 500 cycles at 5 C. The LIC assembled with activated carbon (AC) cathode and such a CNTs/LTO composite anode displays excellent energy storage properties, including a high energy density of 35 Wh kg^?1 at 7434 W kg^?1, and a high capacity retention of 87.8% after 2200 cycles at 1 A g^?1. These electrochemical performances outperform the reported data achieved on other LTO anode-based LICs. Considering the facile and scalable preparation process proposed herein, the CNTs/LTO composites can be very potential anode materials for hybrid capacitors towards high power-energy outputs.     

Stabilizing temperature-capacitance dependence of (Sr,Pb, Bi)TiO3-Bi4Ti3O12 solutions for energy storage

(1-x)Sr_0.7Pb_0.15Bi_0.1TiO₃-xBi₄Ti₃O₁₂ ((1-x)SPBT-xBIT, x = 0-0.125) bulk ceramics were developed and calcined via the solid-state method, aimed at the application of pulsed power capacitors. The phase structures, temperature stability, hysteresis loop, and discharge properties were systematically investigated. Considering both the temperature stability and dielectric properties, 0.925SPBT-0.075BIT bulk ceramics with a capacitance variation satisfying the X7R specification were developed for pulsed power capacitors. The energy storage density was 0.252 J/cm³, and the ceramics showed high temperature stability at 80 kV/cm. The discharge current waveforms of the 0.925SPBT-0.075BIT ceramics were recorded. A high discharge power density of approximately 1.01 × 10⁸ W/kg with an 8 Ω load resistor and short discharge period of 84 ns were achieved at 50 kV/cm. The good temperature stability properties and high power density show that the 0.925SPBT-0.075BIT ceramics are well suited for pulsed power capacitors with a wide temperature range.     

开关磁阻直线电机的设计及其推力优化

设计了一种开关磁阻直线电机,使用JMAG软件对其进行了仿真和优化。进行了推力公式的推导,研究了导通顺序和初始位置对电机推力的影响,并分析了三种典型情况的磁力线分布。对电机的定子和动子的齿部和轭部高度、宽度及铁耗进行仿真优化,得出了最优参数。将有取向硅钢应用于该电机,研究了推力与轧制角的关系,并与使用普通硅钢的开关磁阻直线电机进行了对比,推力有一定提升。提出在动子齿部开切向槽的方案,结果表明,开切向槽对推力的影响较小,并能显著减小推力波动。     

A new polymer electrolyte poly(acrylonitrile)-dimethylsulphoxide-salt for electrochemical capacitors

The PAN-DMSO-Et₄NBF₄ and PAN-DMSO-Et₄NTf (Tf is triflate ion) electrolytes were prepared as white, turbid foils with a thickness in the range of 0.1-0.5 mm, using the casting technique. Room temperature conductance of the electrolytes, detected from ac impedance experiments, was at the level of 8 and 14 mS cm⁻¹ for Et₄NBF₄ and Et₄NTf salts, respectively. The electrochemical stability window of approximately 2.6-2.8 V was estimated using a glassy carbon electrode. Temperature dependence of the conductivity is of the Arrhenius-type for both electrolytes, with an activation energy of approximately 34 kJ mol⁻¹. The double-layer capacitors built with these electrolytes, serving both as separators and activated carbon powder (ACP) binders, showed a specific capacity of 50 F g⁻¹ of carbon material. Capacitors were assembled by sandwiching the PAN-DMSO-salt electrolyte between two PAN-salt-DMSO-ACP-AB electrodes and pressing across the system; the resulting devices had a coin-like shape with 8 mm diameter and thickness between 2.0 and 2.5 mm.     

电磁发射兵器用电容器的选取

本文首先从理论上论述了膜电容器的储能密度与寿命之间的关系，对国际电容器制造水平和趋势进行了分析，提出采用干式金属化膜电容器作为储能元件。最后，根据电磁发射兵器整体寿命配合原则，提出高储能密度脉冲电容器的合理寿命指标。     

超级电容器在汽车启动中的应用

根据超级电容器的结构特性,介绍在汽车启动过程中如何利用超级电容器减小对车内其他电子设备的干扰,改善汽车的启动性能,延长蓄电池使用寿命.     

基于开关电流技术的连续小波变换的实现方法

开关电流技术是一种新的模拟抽样数据处理技术。开关电流电路具有一般电路不具有的优点，与标准数字CMOS工艺兼容。连续小波变换是分析非平稳信号的有力工具，在信号处理上有广泛的应用。本文提出用开关电流技术实现连续小波变换的方法，并用Matlab仿真证明了其理论可行性。     

一种速度优化的流水线模数转换电容误差平均技术

无源电容误差平均技术是一种本质线性(Inherently Linear)的流水线模数转换电容失配校准技术,但其转换速度是传统技术的一半.为了提高速度,本文提出了一种改进的电容误差平均技术.该技术从减少一个转换周期所需的时钟相数目和减少每个时钟相的时间两个方面来优化速度.电路分析和MATLAB仿真表明,在两种典型的情况下,改进的技术能将速度提高52%(跨导放大器为开关电容共模反馈)和64%(跨导放大器为非开关电容共模反馈)以上.改进的技术更适用于高速高精度及连续工作的应用场合.     

开关稳压电源用铝电解电容器的失效机理

概述了开关稳压电源用铝电解电容器的工作状态和失效模式，着重讨论了开关稳压电源用铝电解电容器的开路失效和击穿失效机理。