岩石物理横波速度曲线计算技术

横波速度是地震勘探中的重要参数。针对实际生产中缺乏横波速度测井曲线资料，利用经验公式计算精确度不高的问题，通过对横波速度计算理论模型的研究分析，选择Blot-Gassman模型法，利用岩石矿物成分、流体成分、孔隙度及密度等测井曲线进行横波速度测井曲线的计算，并对横波速度计算技术和流程进行研究。在实际工区进行了横波速度曲线计算，计算结果与实测横波吻合程度较高，误差小于10％，该技术在储层和流体识别预测的应用中取得了较好效果。     

自旋式脱接器在临盘油田的应用

为保障临盘采油厂的大泵井正常生产 ,购进了自旋式脱接器。这种脱接器由上体和下体两部分组成 ,上体包括轨道管和轨道套 ;下体包括接头、挡圈、弹簧、滑套和中心杆。自旋式脱接器可在任意位置和角度对接和脱开 ,对接和脱开时只需下放和上提抽油杆柱即可完成。当泵砂卡时 ,左旋抽油杆柱即可脱开 ,解决了砂卡井脱接器不能脱开的难题。该脱接器可重复对接12 0次以上 ,耐疲劳寿命 7× 10 7次以上     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

内管注水泥固井工具的研究与分析

内管注水泥技术是针对大尺寸套管和表层套管固井的特点及特殊要求而采用的一种固井技术，具有省时、替量少等特点，在现场得到大量推广应用。内管注水泥器是内管固井技术的关键工具，其性能好坏直接影响到固井质量。对各种内管注水泥固井工具的结构及特点分别进行了分析研究，并就其发展方向提出建议。     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

一种基于GE90-30PLC的飞剪自动控制系统

本文介绍了调整线材轧线精轧机前专用于切头的启停式飞剪的自动控制系统。该系统以GE90—30PLC为控制核心，辅以热金属HMD、光电编码器等元件，能很好地完成飞剪的剪切及定位。其中着重阐述了飞剪控制中各个重要参数的计算原理和方法。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

水闸闸室化算梯形横截面上不平衡剪力的分配计算

当地弹性地基梁法计算非岩石地基的水闸底板应力时，首先要求解出不平衡剪力，当闸墩截面选择梯形时（主要是边墩），常用方法是作图法，这既有误差又繁琐。所以就此推导出一个公式，可直接求解平衡剪力。     

圆杆弹性和弹—塑性扭转公式的探讨

对圆杆在线弹性阶段，弹－塑性阶段和全塑性阶段的扭转剪应力的计算公式作了分析，并推导了在材料的应力－应变关系（τ－γ关系）不服从虎克定律时，扭转真实剪应力的计算公式。文中对扭转强度计算公式的来源，物理含义及其都作了详细的说明。这对执行和理解国家ＧＢ１０１２８－８８《金属室温扭转试验方法》是有益的，而且对高校中材料力学的教学具有一定的参考价值。