带通采样在数据采集中的应用研究

在数据采集中采用带通采样，可大大降低采样率，但系统中的抗混叠滤波器会造成相位的非线性。采用对滤波后的信号进行带通采样，然后再用FRR滤波器校正相位的非线性，从而不失真地还原原信号，最后在Matlab中进行仿真，验证了该方法的有效性。     

Bandpass filters using periodically loaded combline resonators

A novel combline filter is proposed for cellular‐radio base stations. The Q‐factor is significantly improved. The eigenvalue equation is expressed with the single‐team approximation in the gap region of the combline resonator. A two‐pole combline filter is designed. The calculation, simulation, and experiment results are presented and are in good agreement. © 2005 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

Results of the ASTM field test of tristimulus weighting functions

In 1993, the American Society for Testing and Materials carried out a field test of newly calculated tristimulus weighting factors. These weighting factors had been calculated by a method proposed by Venable. the test also included a method of correction for bandpass dependence put forth by Stearns. the purpose of the trial was to assess the possible reduction in bandpass dependence introduced by each of these sets of weights. A large number of sets of spectral data were gathered from the cooperators in the field test. Results of integration by the various sets of tristimulus weighting factors were calculated. A total of 15 120 color differences were calculated and statistics were derived to test the probable error resulting from each method of correction. Errors attributable to bandpass dependence were on the order of a few tenths to as much as one CIELAB unit when uncorrected weight sets were used. These errors could be reduced to a few hundreths of a CIELAB unit, and in some cases to a few thousandths of a unit, by employing one correcting strategy or the other. an overall mix of strategies was ultimately chosen to minimize the bandpass dependence over the entire range of weight sets. Utilizing this mixed strategy, the median error introduced into 10-nm integration by bandpass dependence was only 0.004 CIELAB units. © 1995 John Wiley & Sons, Inc.     

短开路耦合谐振器加载的宽带带通滤波电路

提出了一种基于短开路耦合器加载的宽带带通滤波电路. 该滤波电路通过在输入和输出端口之间,并连加载短路耦合微带谐振器和开路耦合微带谐振器实现5个传输极点和3个传输零点的带通选择特性. 对所提出的短开路耦合谐振器进行了奇偶模理论分析,揭示了其传输零极点形成的物理机理. 最后,对所提出的滤波电路进行了加工测试. 测试结果表明,所提出的宽带滤波电路能够在2.0～4.2 GHz频率范围内实现 3 dB 带通传输,工作相对带宽为73%,仿真和实测结果吻合较好.     

The design and test of dual/triple‐mode bandpass filter based on temporal coupled‐mode theory

In this article, the design and test of both a K‐band dual‐mode bandpass filter (BPF) pair and a K‐band triple‐mode BPF are presented based on N‐mode temporal coupled‐mode theory (CMT). The expressions of transmission and reflection responses are analytically derived. All the parameters in the expressions have clear physical meanings and are easily optimized to reach the required filter performance. Aided by eigenmode simulations, concrete structures of the three integrated BPFs are designed and optimized to approach the calculated physical parameters. After the fabrications and measurements of the three BPFs, extended upper/lower stopband with high stopband rejections are achieved, and by increasing the number of resonant modes, improved frequency selectivity and better passband flatness are obtained. The analytical analysis well predicts the simulation and measurement results, which provides an efficient way for BPF designs. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:609–622, 2016.     

Wide passband/stopband bandpass filter based on transversal signal interference concepts and modified branch‐line structure

A high selectivity wide passband filter with a broader stopband based on transversal signal‐interaction concepts and modified branch line structure (MBLS) is developed in this article. Two transmission paths, that is, one half‐wavelength transmission line and one MBLS, are used to realize signal transmission from Port 1 to Port 2. Then, two transmission zeros are introduced at both lower and upper sides of the passband, which are used to improve the passband selectivity greatly. The filter bandwidth can be easily controlled by reasonable adjusting the coupling coefficient of the coupled lines. Furthermore, with four stubs connected at the input/output ports, the stopband attenuation level is improved greatly. Finally, one prototype filter having 69.1% of 3 dB fractional bandwidth is fabricated with advantages of sharp selectivity and high out‐of‐band rejection. The EM simulated and measured results are presented, and an excellent agreement can be obtained. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:330–336, 2015.     

Novel slotted stepped‐impedance resonator and its application to compact and high performance bandpass filter and diplexer design

By etching slots in the low‐impedance section of the conventional stepped‐impedance resonator, a novel slotted stepped‐impedance resonator (SSIR) is proposed. As two examples, a fourth‐order bandpass filter (BPF) operating at 1 GHz with a size of 0.078 λ_g × 0.062 λ_g and a miniaturized diplexer operating at 0.9/1.57 GHz with a size of 0.054 λ₀ × 0.086 λ₀ are designed based on the proposed SSIR. The fabricated BPF exhibits a high selectivity and a wide ?30 dB rejection upper stopband from 1.13 f₀ to 6.52 f₀, while the fabricated diplexer has up to ?60 dB output isolation. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

射频采样接收机中ADC的设计选型

本文介绍了ADC的性能指标和ADC器件选择的一般标准,并针对软件无线电中现有的射频采样接收机的模型,定量地分析了相应的ADC选择指标,并对相应模型的优劣进行了深入讨论。     

差分无源器件的设计

在现代无线通信系统中,差分电路相比单端电路而言具有更强的抗干扰能力,因此受到了国内外学者的广泛关注。文章介绍了混合模散射参数、差分器件设计中常用的微带线和缝隙线及两种传输线之间的相互转化,并介绍了基于微带线和缝隙线转换结构的两种全差分带通滤波器。两种滤波器分别实现了多频段和宽带的差模传输特性以及宽带的共模抑制特性。文章还给出了差分耦合器、差分功分器和差分天线等差分器件的设计。仿真与实测结果吻合较好,验证了设计方法的正确性。     

宽阻带小型化双频带通滤波器

文中提出了一种具有宽阻带的紧凑型双频带通滤波器,它采用了折叠短路枝节负载谐振器、紧凑型微 带单元谐振器(CMRC)和阶跃阻抗谐振器结构。由于多个谐振器产生了五个可控传输零点(TZ),该滤波器实现了两个 通带之间的良好隔离度以及宽阻带特性。制作并测试了尺寸紧凑的双频带通滤波器实验样品,测试结果显示,第一通 带和第二通带的中心频率/ 插入损耗分别为0. 66 GHz/0. 8 dB 和1. 73 GHz/0. 7 dB,阻带频率高达10. 5 GHz,抑制水平 超过15 dB。