离心泵并联运行工况点的数值求解

建立了求解多台不同型号离心泵并联运行工况点的数学模型,给出了用数值计算中的“二分法”求解该模型的方法,并附有用Exce l计算的实例。     

复合材料一体化钻井泵缸套产业化技术研究

介绍了复合材料一体化钻井泵缸套在产业化过程中的若干关键技术。通过对缸套内套材料成分和组织的优化研究,双液分时离心浇注工艺优化研究以及双液离心浇注工装开发,实现了新工艺缸套的产业化。与现行的热镶装双金属缸套工艺相比,采用新技术生产的缸套平均使用寿命超过750h,生产成本下降了20%。     

低温高速离心泵的研制与应用

阐述了适合于输送低温介质的高速离心泵的水力设计和结构设计方法，结构上采有长，中，短叶片相间的复合叶轮及双密封结构，理论上采用以效率为目标函数的优化水力设计方法，保证了低温高速离心泵具有很好的工人可靠性和优越的性能指标。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

液化石油气磁力泵改造

对输送液化石油气磁力泵在运行1个月后出现的故障进行了分析,提出了在磁路、气路及安装等方面采取的一些改进措施。     

潜油电机碟形弹簧的动力学分析

为了降低潜油电泵机组的振动对止推轴承性能的影响,在潜油电机中节和下节的止推轴承静块底部安装了蝶形弹簧。用有限元方法进行模态分析,确定了蝶形弹簧的主振型和固有频率,然后进行瞬态动力学分析,求解蝶形弹簧在一定载荷下的应力和位移。依此设计的蝶形弹簧将进一步延长止推轴承的使用寿命。     

空调器中多翼离心风机的噪声研究及结构优化

采用逐步回归法对大量的多翼离心风机实验数据进行拟合,针对家用空调行业中以噪声为其最重要 的考核标准,得出了噪声与叶轮结构参数及风机性能参数间的近似关系式,并以噪声为目标函数进行了优化计算。     

Performance of unitary heat pumps: review of ASHRAE Symposium session

1. 1. System design optimization and validation for single-speed heat pump by S.K. Fischer and C.K. Rice, Oak Ridge National Laboratories.

2. 2. Analysis of on/off cycling for an air-to-air heat pump operating in the heating mode by W.A. Miller, Oak Ridge National Laboratories.

3. 3. Field measured cycling, frosting and defrosting losses for a high efficiency air source heat pump by V.D. Baxter and J.C. Moyers, Oak Ridge National Laboratories.

4. 4. Design and available energy analysis of a heating-only residential heat pump for the Western Pacific Northwest by D.E. Elger, C.M. Reistad and S. Lang, Oregon State University.

5. 5. A study of heat pump service life by Nance C. Lovvorn, Alabama Power Company and Carl C. Hiller, Electric Power Research.

Computer analysis,design and simulation of horizontal ground heat exchangers

This paper presents a new computerized procedure for dealing with the design of horizontal ground heat exchangers (HGHE). The computer program is based on the transient model of coupled nonlinear partial differential equations governing heat and mass flow in soils. The model is two-dimensional and delineates the operation of ground heat storage with the HGHE and such phenomena as freezing/thawing and drying/rewetting of soil moisture. Comprehensive climatological data, such as ambient temperature, solar radiation, wind velocity, rainfall, snowfall, snow characterstics, and water vapour pressure is used to simulate conditions at the ground surface over any required length of time. The package can be applied to any geographical location by changing climatic and soil data input. The designer has the possibility of selecting any of 12 types of soils from sand to clay, 12 commercial heat pumps, nine different configurations of the HGHE, 16 plastic pipes for ground coils, and 13 ground coil fluids. The program, however, does not calculate the length of the HGHE but it evaluates the thermodynamic performance of a ground heat pump system and provides comprehensive data on thermal and hydraulic conditions in ground heat storage. The length of the ground heat exchanger is obtained from a line source theory model or from site dimensions and pipe spacing. Computed results for ground heat exchanger operation correlate fairly well with experimental data. Simulation of temperature and moisture content in the ground for natural conditions (no heat extraction/deposition) showed a fair agreement with field data. The entire computer program is user-friendly, interactive, menu-driven, and written in FORTRAN 77.     

流程离心泵变频调速的实践与探讨

探讨了变频调速在流程离心泵上应用的可行性，同时阐述了变频调速器功率的确定及其使用效果。