自适应阵对角线加载研究

本文分析了对角线加载对自适应阵性能的影响，提出了加载门限的概念，以及加载门限的计算公式，为加载量的选取提供了方法和依据，并将加载研究的结果加以推广，提出了有效的ＬＳ自适应波束形成算法的非零初始化方法。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

Rheological and drug‐release behaviour of a scleroglucan gel matrix at different drug loadings

The aim of this study was to investigate the drug‐loading effects on release and mechanical properties of a scleroglucan gel, with the intention of considering them in delivery systems formulations. The rheological and kinetic properties of a 2 % w/w scleroglucan gel matrix loaded with 0, 0.02, 0.04, 0.06, 0.2 and 0.4 % w/w of theophylline (Th, used as a model drug) were investigated. Rheological measurements were performed in a controlled‐stress rotational‐shear rheometer under isothermal conditions. For theophylline release from the gel a flat Franz cell was used and the kinetic parameters were derived applying a semi‐empirical power law. The influence of scleroglucan molar weight on kinetic and rheological behaviour was also studied. Results suggest two possible effects of drug loading on the gel network: in the 0.04–0.06 % w/w Th range a plasticizing effect and in the 0.2–0.4 % w/w Th range a rigidization effect. In the first range mentioned, the changes in the gel structural properties tested by means of rheological measurements are coincident with changes in drug‐release kinetics. Copyright © 2005 Society of Chemical Industry     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

未增塑聚氯乙烯(PVC-U)异型材配方基础

PVC-U异型材配方十分复杂,常用原料通常在10种以上。根据大连实德集团实际生产情况,这10多种原料通常以7大组分的方式进行配料和生产。文中就该配方中7大组分的分类、特点及应用情况分别进行了详细介绍。     

Dynamic response and behavior of reinforced concrete slabs under impact loading

Reinforced concrete slabs are among the most common structural elements. In spite of the large number of slabs designed and built, the effect of their details on their behavior under impact loads are not always appreciated or properly taken into account. This experimental study was aimed at understanding the dynamic behavior of structural concrete slabs under impact loading to improve the state of the art of protective design. This study investigated the effects of different types of slab reinforcements and the applied impact loads on the dynamic response and behavior of reinforced concrete slabs.     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Equipment for Testing Sheet Structural Materials under Biaxial Tension. Part 2. Testing by Biaxial Loading in the Plane of the Sheet

We analyze specific features of the design of equipment used for mechanical testing of sheet structural materials under the conditions of biaxial static, cyclic, or dynamic loading. We propose original solutions of the problems related to the fatigue testing of crosslike specimens performed without using complex hydraulic systems and their dynamic testing carried out by using very simple testing machines for uniaxial tension–compression.