Large domain-wall currents in epitaxial Au/BiFeO3/SrRuO3 thin-film capacitors with modulated oxygen vacancy and wall densities

Large domain wall (DW) conductivity in an insulating ferroelectric plays an important role in the future nanosensors and nonvolatile memories. However, the wall current was usually too small to drive high-speed memory circuits and other agile nanodevices requiring high output-powers. Here, a large domain-wall current of 67.8 μA in a high on/off ratio of ~4460 was observed in an epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitor with the minimized oxygen vacancy concentration. The studies from read current-write voltage hysteresis loops and piezo-response force microscope images consistently showed remaining of partially unswitched domains after application of an opposite poling voltage that increased domain wall density and wall current greatly. A theoretical model was proposed to explain the large wall current. According to this model, the domain reversal occurs with the appearance of head-to-head and tail-to-tail 180° domain walls (DWs), resulting in the formation of highly conductive wall paths. As the applied voltage increased, the domain-wall number increased to enhance the on-state current, in agreement with the measurements of current-voltage curves. This work paves a way to modulate DW currents within epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitors through the optimization of both oxygen vacancy and domain wall densities to achieve large output powers of modern domain-wall nanodevices.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Experimental and numerical study on compressive performance of perforated brick masonry after fire exposure

This paper discusses the compressive performance of perforated brick masonry after fire exposure. Compressive strength tests of the mortar, clay perforated brick, and perforated brick masonry specimens were performed in accordance with ISO834 fire tests of different durations. The temperature distribution of the masonry materials and specimens was simulated using the finite element software ABAQUS, with the thermal parameters of masonry materials recommended by European standard Eurocode 6 and related literature. The compressive strength reduction factors of mortar and clay perforated brick exposed to different fire durations were calculated via the layered method suggested by European standard Eurocode 1. In addition, the compressive strength reduction factors after cooldown were obtained from the experimental data of the masonry materials, and by considering further reductions in the compressive strength after cooling from high temperatures. Experimental data of the masonry specimens were compared with the numerical results obtained using the reduction factors proposed in this work. The comparison revealed an overall acceptable approximation. Thus, the method presented in this paper can be used to evaluate the residual capacity of masonry structures after fire.     

墙体裂缝的成因及防治

介绍了墙体裂缝的种类，从地基不均匀下沉、温度变化等方面分析了引起墙体裂缝的原因，介绍了墙体裂缝的预防措施和治理措施，以有效控制墙体裂缝的危害程度。     

浅谈无缝钢管的壁厚偏差

通过探讨、分析无缝钢管壁厚偏差产生的原因，提出了改善钢管壁厚偏差的一些措施，并结合实际生产，得出了比较满意的结果。     

DIRECT RESONANCE OF TURBULENT BOUNDARY LAVER OVER COMPLIANT WALLS

１．　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｍａｉｎｇｏａｌｏｆｔｈｉｓｐａｐｅｒｉｓｔｏｅｘｐｌｏｒｅｔｈｅｐｏｓｓｉｂｉｌｉｔｙｔｏｌｅａｒｎｍｏｒｅａｂｏｕｔｔｈｅｍｅｃｈａｎｉｓｍｏｆｔｕｒｂｕｌｅｎｔｂｏｕｎｄａｒｙｌａｙｅｒｆｌｏｗｉｎｔｅｒａｃｔｉｏｎｓａｎｄｉｔｓｅｆｆｅｃｔｓｏｎｃｏｍｐｌｉａｎｔｗａｌｌｐｅｒｆｏｒｍａｎｃｅ．Ｔｈｅｒｅａｒｅｃｅｒｔａｉｎｐｒｅｒｅｑｕｉｓｉｔｅｃｏｎｄｉｔｉｏｎｓｔｏｆｕｒｔｈｅｒｔｈｅｓｔｕｄｙｏｎｔｈｅｍｅｃｈａｎｉｓｍ，ｉ．ｅ．ｔｈｅｃｏ…     

网络安全中的防火墙技术

介绍了防火墙的原理、分类及其应用     

混凝土小型砌块建筑裂缝宽度的标准设置研究

通过对混凝土小型空心砌块单片墙进行试验 ,了解不同构造措施墙体的初始裂缝在墙体上出现的部位、形态、发展规律以及墙体最终破坏形态 ,并通过试验明确墙体在不同受力状态下的裂缝形态 ,最后根据试验结果初步提出混凝土小型空心砌块建筑的裂缝宽度控制标准