水平岩层软弱基座危岩体演化过程研究

以重庆市甄子岩29号危岩体为研究对象，基于现场调查和分析解剖，建立UDEC离散元数值计算模型，对其演化变形过程进行模拟分析。研究表明，在巨大的自重作用下，由于基座岩体岩质软，岩体较破碎，且基座外侧为直立的陡崖，具有完整的临空面，从而使基座岩体易发生压缩流变及剪切流变，进而使危岩体存在滑移垮塌的危险。     

裸眼井中扩张式封隔器力学行为研究

封隔器在石油天然气开采中起着非常重要的作用,而扩张式封隔器在裸眼井中广泛应用。本文采用有限元软件建立了裸眼封隔器与地层的模型,对胶筒在坐封过程中与井壁接触应力的变化进行了研究,并研究了在不同摩擦系数下接触压力的变化,结果表明,建立粗糙井壁面能够更加符合实际情况,胶筒肩部为应力集中的区域,地层与胶筒的接触应力会随着摩擦系数的增加而减小。研究结果为裸眼扩张式封隔器的设计和改进提供了理论依据。     

压裂水平井产能预测方法研究进展

水平井压裂技术在低渗透及非常规储层中得到了广泛应用,压裂后水平井的产能预测关系到油田开发方案的制定,因此,国内外学者对压后渗流模型的建立和求解方法做出了不懈的努力。本文详细回顾了国内外学者所建压裂水平井产能预测模型及求解方法,指出了不同模型和求解方法的优缺点,并展望了压裂水平井产能模型的发展方向。     

水力旋冲钻井工具破岩影响因素模拟及应用

常规的冲击钻井工具不能满足井眼轨迹控制要求、使用寿命有限、缓解脱压不显著等问题,影响了在定向井钻井中的推广应用。建立ø215.9 mm PDC钻头和岩石的有限元模型,分析钻井参数对破岩效率的影响规律,结果表明:冲击频率为17.5 Hz和35 Hz时,破岩效率最优; 破岩效率随钻压增大而增加,而后变化逐渐平缓; 破岩效率随钻头转速增大而增加; 破岩效率随冲击载荷的增加变化平缓。据此研制了新型水力旋冲钻井工具。现场试验表明,该工具符合定向水平井“一趟钻”工艺要求,使机械钻速提高56%,使用寿命达150 h,MWD信号正常。     

Mechanical properties of a self-healing fibre reinforced epoxy composites

Inspired by biological systems in which damage triggers an autonomic healing response, a polymer composite material that can heal itself when cracked has been developed. In this work, compression and tensile properties of a self-healed fibre reinforced epoxy composites were investigated. Microencapsulated epoxy and mercaptan healing agents were incorporated into a glass fibre reinforced epoxy matrix to produce a polymer composite capable of self-healing. The self-repair microcapsules in the epoxy resin would break as a result of microcrack expansion in the matrix, and letting out the strong repair agent to recover the mechanical strength with a relative healing efficiency of up to 140% which is a ratio of healed property value to initial property value or healing efficiency up to 119% if using the healed strength with the damaged strength.     

Vertical cyclic loading response of geosynthetic-encased stone column in soft clay

Dynamic responses of the geosynthetic-encased stone column (GESC) supported embankment under traffic loads have become a hot topic. This study investigates the responses of GESC improved ground under vertical cyclic loading. A series of laboratory tests in a designed model test tank have been carried out with different loading parameters (varied loading amplitudes and frequencies), different column dimensions (varied encasement lengths and column diameters). In the tests, the soil-column stress distribution, accumulated settlement of loading plate, excess pore water pressure in the surrounding soil and lateral bulging of the stone column are monitored. Experimental results indicate that the vertical stress on the stone column increases with the increment of encasement length, and decreases with the increment of column diameter, loading amplitude and loading frequency. The increasing stress on the surrounding soil leads to a greater accumulated settlement of the loading plate and excess pore water pressure, while the increasing stress on the column leads to larger lateral bulging of the column. Excess pore water pressure dissipates effectively through vertical and horizontal drainage channels provided by the stone column and the sand bed. The geosynthetic encasement prevents the clay from obstructing the drainage channel by filtration and guarantees the drainage effect.     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

Ultimate bearing capacity of strip footing resting on clay soil mixed with tire-derived aggregates

This study investigated the use of recycled tire-derived aggregate (TDA) mixed with kaolin as a method of increasing the ultimate bearing capacity ( UBC) of a strip footing. Thirteen 1g physical modeling tests were prepared in a rigid box of 0.6 m × 0.9 m in plan and 0.6 m in height. During sample preparation, 0%, 20%, 40%, or 60% (by weight) of powdery, shredded, small-sized granular (G 1–4 mm) or large-sized granular (G 5–8 mm) TDA was mixed with the kaolin. A strip footing was then placed on the stabilized kaolin and was caused to fail under stress-controlled conditions to determine the UBC. A rigorous 3D finite element analysis was developed in Optum G-3 to determine the UBC values based on the experimental test results. The experimental results showed that, except for the 20% powdery TDA, the TDA showed an increase in the UBC of the strip footing. When kaolin mixed with 20% G (5–8 mm), the UBC showed a threefold increase over that for the unreinforced case. The test with 20% G (1–4 mm) recorded the highest subgrade modulus. It was observed that the UBC calculated using finite element modeling overestimated the experimental UBC by an average of 9%.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.