锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

Reaction between the tetragonal tungsten bronze niobate K2Sr4Nb10O30 and the perovskite Pb(Mg1/3Nb2/3)O3

The search for dielectric materials with a high dielectric constant and ′_r = ƒ(T) curves with a flat profile fitting the X7R specification is still ongoing. Promising results were obtained by mixing compounds with closely related structures, such as the tetragonal tungsten bronze (TTB) niobate K₂Sr₄Nb₁₀O₃₀ and the perovskite Pb(Mg_1/3Nb_2/3)O₃ (PMN). The present study, based on three methods of synthesis, explores the origin of the spreading out of the dielectric curves ′_r = ƒ(T). For the composition 10x K_0.2Sr_0.4NbO₃ (KSN) + (1 − x)Pb(Mg_1/3Nb_2/3)O₃ (PMN) with x = 0.3–0.6, the three synthesis methods provided similar characteristics and for the highest perovskite ratio (x = 0.3), the ′_r = ƒ(T) curve exhibits a flat profile. When lithium is used as a sintering agent, ′_r = ƒ(T) curves present a linear dependency with the temperature. These materials are also characterized by a structural and a microstructural inhomogeneity. Two phases TTB and perovskite type, different from KSN and PMN, are present after calcination and sintering, but not evenly distributed. The PbO loss during sintering also contributes to the evolution of the properties of the material.     

用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。     

Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.     

用于微波/射频集成电路的一种新型低损耗介质——多孔硅及氧化多孔硅厚膜

提出在单片微波集成电路(MMIC)中用多孔硅/氧化多孔硅厚膜作微波无源器件的低损耗介质膜.研究了厚度为70μm的多孔硅/氧化多孔硅厚膜在低阻硅衬底上的形成,这层厚膜增加了衬底的电阻率,减少了微波的有效介质损耗.通过测量在低阻硅衬底上形成的氧化多孔硅厚膜上的共平面波导的微波特性,证明了在低阻硅衬底上用厚膜氧化多孔硅可以提高共平面传输线(CPW)的微波特性.     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

A Finite Element Computational Method for Gas Hydrate. Part I: Theory

A finite element scheme is presented to model the dissociation of gas hydrates in porous media by hot water injection. We show a complete derivation of the finite element formulation, including the associated mass and energy conservation equations capable of performing transient analysis of both conductive and convective heat transfer for gas and liquid flow in porous media. The scheme also includes the latent heat effect to accommodate the change of phase due to melting of hydrate. In the companion paper, Part II, this method is successfully applied to hydrate reservoirs.     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

P／MCs新型复合材料制备、结构及阻尼性能

采用特殊的渗流法所制备的新型Ｐ／ＭＣｓ复合材料，由高分子聚合物与蜂窝状铝架组成，它具有优异的阻尼性能，并简述了结构对阻尼的影响