Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

稀土石膏常压酸化法制备硫酸钙晶须的研究

以含稀土的石膏为原料运用常压酸化法合成硫酸钙晶须,探讨了不同工艺条件对生成的硫酸钙晶须形貌的影响,同时还考察了晶型助长剂的种类和晶型助长剂的含量对硫酸钙晶须生长的影响,利用SEM和XRD分别对硫酸钙晶须的表面形貌、物相特征做了表征分析。实验得到制备硫酸钙晶须的最佳的反应条件：稀土石膏质量浓度为0.22 g/mL、反应时间为25 min、盐酸浓度为2.8 mol/L、反应温度为70 ℃、陈化时间为4 h,在此条件下合成的硫酸钙晶须平均长度为61 μm,平均长径比为30.5;通过对比实验选出了CuCl₂作为促进硫酸钙晶须生长的助长剂,在添加5%（质量分数）的CuCl₂的情况下可使硫酸钙晶须长径比从30.5增至41,长度从61 μm增至81 μm。     

加氢反应器头盖密封质量控制探讨

加氢反应器是加氢装置的重要组成部分,反应器头盖因工况复杂,导致密封难度较大,密封不严,会导致整个装置不能正常运转。为此,就其头盖拆装及密封问题进行探讨,提出有效的质量控制措施。     

迷宫螺旋泵和密封工作特性研究

介绍了一种实测迷宫螺旋泵和密封工作特性的实验方法,通过该方法可以测得迷宫螺旋泵的泵送特性曲线、迷宫螺旋端面组合密封的最大密封压力以及端面开启的开始转速,具有一定的实用价值。     

T-ZnO晶须增强环氧树脂复合材料的力学行为

研究了以四脚状氧化锌（T-ZnO）晶须为增强剂，环氧树脂复合材料的力学行为。结果表明，由具有三维空间结构的T-ZnO晶须为增强剂所制备的环氧树脂复合材料具有各向同性的力学性能，T-ZnO晶须填加质量分数为6%时，就可使材料的力学性能改善；拉伸强度提高到169%，拉伸功几乎提高了100%，冲击强度提高到300%，抗弯的断裂功提高到158%，而压缩强度略有下降。     

可控式机械密封设计

从机械密封的工作原理和失效分析入手,将自动控制技术引入机械密封,以改进机械密封的性能,使机械密封装置能够主动适应操作条件和工作环境的变化,提高其工作的可靠性和使用寿命,适用于要求较高的流体机械的轴端密封。     

晶须取向对SiCw/6061Al复合材料热压缩变形行为的影响

采用SEM 和 Magiscan-2A 图像分析系统研究了晶须取向对SiCw/6061Al复合材料在300℃压缩变形行为的影响.结果表明:晶须取向影响着晶须折断程度和转动角度; 随着晶须取向角的增加,晶须转动和折断行为所导致的软化效果下降.同时晶须取向也影响复合材料的热压缩应力-应变曲线的形状.在热压缩变形过程中,晶须取向角为0°和30°的复合材料表现出明显应变软化现象, 晶须取向角为45°的复合材料无明显软化现象.晶须取向角为90℃的复合材料表现出应变硬化现象.     

罗茨真空泵主轴输入端动密封问题探讨

分析了罗茨真空泵轴封漏油的原因，介绍了提高轴封有效性的措施。     

低温高速离心泵的研制与应用

阐述了适合于输送低温介质的高速离心泵的水力设计和结构设计方法，结构上采有长，中，短叶片相间的复合叶轮及双密封结构，理论上采用以效率为目标函数的优化水力设计方法，保证了低温高速离心泵具有很好的工人可靠性和优越的性能指标。