Uncertainties in the determination of pyrrolizidine alkaloid levels in naturally contaminated honeys and comparison of results obtained by different analytical approaches

The contamination of honey with hepatotoxic pyrrolizidine alkaloids (PAs) is a well-known hazard for food safety. While management strategies and controls of the honey industry aim to reduce the PA levels, uncertainties remain with regard to the safety of regionally produced and marketed honey. In addition, a previous study showed large differences of results obtained after various periods of storage and apparent differences between the analytical results of different laboratories. Therefore, this study aimed at examining these uncertainties by monitoring the impact of storage on the PA and PA N-oxide (PANO) content of two freshly harvested honeys and on possible demixing effects caused by pollen settling. Additionally, three analytical approaches – target analysis with matrix-matched calibration or standard addition and a sum parameter method – were applied for a comparative analysis of 20 honeys harvested in summer 2016. All samples originated from Schleswig-Holstein in Northern Germany where the PA plant Jacobaea vulgaris is currently observed on a massive scale. The results of the time series analyses showed that PANO levels markedly decreased within a few weeks and practically reached the LOD 16 weeks after harvest. Tertiary PAs, by contrast, remained stable and did not increase as a consequence of PANO decrease. The experiments on a putative demixing, which may result in a heterogeneous distribution of PAs/PANOs, revealed that there was no such effect during storage of up to 12 weeks. A comparison of the PA/PANO levels obtained by different analytical approaches showed that in some cases the sum parameter method yielded much higher levels than the target approaches, whereas in other cases, the target analysis with standard addition found higher levels than the other two methods. In summary, the results of this study highlight uncertainties regarding the validity and comparability of analytical results and consequently regarding health risk assessment.     

NNI-1型C_5/C_6烷烃异构化催化剂长周期运行分析及建议

中国石化海南炼油化工有限公司0.2 Mt/a C5/C6烷烃异构化装置以连续重整装置的拔头油为原料,使用NNI-1催化剂,采用一次通过流程,不设脱异戊烷塔和稳定塔,经设在连续重整装置内的脱丁烷塔稳定处理后作为汽油调合组分。该装置于2006年9月开工投产,截至2015年3月已连续运行3个周期。长周期运行分析结果表明:前两个周期中NNI-1催化剂具有较高的异构化活性及选择性,C5异构化率为60%左右,C6异构化率为80%左右,C6选择性为15%左右,产品辛烷值基本达到技术指标要求(RON≥78);而在第三周期运行中,催化剂积炭增加等原因导致其异构化活性及选择性降低,异构化产品辛烷值提升能力呈现逐步衰减的趋势,提高反应苛刻度已不能弥补催化剂活性下降造成的产品辛烷值降低。为保证装置长周期运行,建议择机停工对催化剂进行再生,或是直接换用与装置原料性质匹配的异构化催化剂。     

Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

Effects of different carbon sources and C/N values on nonvolatile taste components of Pleurotus eryngii

Pleurotus eryngii, the second largest industrial cultivation mushroom in China, is usually cultivated on substrates mainly consisting of sawdust and corncob. In this study, experiments were performed to determine the effects of different carbon sources and C/N values on nonvolatile taste components of P. eryngii. The effects of different carbon sources on nonvolatile taste components levels revealed that sawdust was beneficial to high levels of crude protein, amino acids, 5′‐nucleotides and equivalent umami concentration, while corncob was beneficial to high contents of carbohydrate, polysaccharides and trehalose. At the similar C/N values, relatively higher sawdust content was beneficial to umami amino acid production, while relatively higher corncob content was beneficial to high contents of carbohydrate, polysaccharides and mannitol. Higher C/N value was beneficial to high levels of crude protein, amino acids, 5′‐nucleotides and equivalent umami concentration, while lower C/N value was beneficial to high contents of carbohydrate, polysaccharides and trehalose. These results provided information for P. eryngii fruit body industrial cultivation to obtain specific nonvolatile taste components with high levels.     

Decomposition of first-order hybrid Petri nets for hierarchical control of manufacturing systems

Although hybrid Petri net (HPN) is a popular formalism in modelling hybrid production systems, the HPN model of large scale systems gets substantially complicated for analysis and control due to large dimensionality of such systems. To overcome this problem, a typical approach is to decompose the net into subnets and then control the plant through hierarchical or decentralized structures. Although this concept has been widely discussed in the literature for discrete PNs, there is a lack of research for HPNs. In this paper, a new method of decomposition of first-order hybrid Petri nets (FOHPNs) is proposed first and then the hierarchical control of the subnets through a coordinator is introduced. The advantage of using the proposed approach is validated by an existing example. A sugar milling case study is analysed by using a decomposed FOHPN model and the optimization results are compared against the results of the approaches presented in other papers. Simulation results show not only an improvement in production rate, but also show the ability to control the plant online. In addition, by using the hierarchical control structure for an FOHPN model, it is possible to reduce the cost of communication links, improve the reliability of the system, maintain the plant locally, and partially redesign the system.     

Deposition,opto-electronic and structural characterization of polymorphous silicon thin films to be applied in a solar cell structure

In this study we analyze the optoelectronic properties and structural characterization of hydrogenated polymorphous silicon thin films as a function of the deposition parameters. The films were grown by plasma enhanced chemical vapor deposition (PECVD) using a gas mixture of argon (Ar), hydrogen (H₂) and dichlorosilane (SiH₂Cl₂). High-resolution transmission electron microscopy images and Raman measurements confirmed the existence of very different internal structures (crystalline fractions from 12% to 54%) depending on the growth parameters. Variations of as much as one order of magnitude were observed in both the photoconductivity and effective absorption coefficient between the samples deposited with different dichlorosilane/hydrogen flow rate ratios. The optical and transport properties of these films depend strongly on their structural characteristics, in particular the average size and densities of silicon nanocrystals embedded in the amorphous silicon matrix. From these results we propose an intrinsic polymorphous silicon bandgap grading thin film to be applied in a p–i–n junction solar cell structure. The different parts of the solar cell structure were proposed based on the experimental optoelectronic properties of the pm-Si:H thin films studied in this work.     

Characteristics and formation mechanism of porosities in CFRP during laser joining of CFRP and steel

An experimental investigation on the mechanism of porosity formation during the laser joining of carbon fiber reinforced polymer (CFRP) and steel is presented. The porosity morphology and distribution were characterized by optical and scanning electron microscopy, and the thermal pyrolysis behaviors were investigated by thermal analysis and designed back-side cooling experiments. The results show that there are two types of porosities in CFRP. Porosity I only appears when the heat input is more than 77.8 J/mm. It has a smooth inner wall and distributes near the bonding interface between CFRP and steel at the central area of melted zone, which is caused by gaseous products such as CO₂, NH₃, H₂O, and hydrocarbons produced by the pyrolysis of CFRP. Porosity II can be seen under all joining conditions. It has a rough inner wall and distributes far away from the bonding interface, concentrating at the final solidification locations. Porosity II is caused by the shrinkage of melted CFRP during solidification stage.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。