Influence of accelerated curing on the compressive strength of polymer-modified concrete

In recent building practice, rapid construction is one of the principal requisites. Furthermore, in designing concrete structures, compressive strength is the most significant of all parameters. While 3-d and 7-d compressive strength reflects the strengths at early phases, the ultimate strength is paramount. An effort has been made in this study to develop mathematical models for predicting compressive strength of concrete incorporating ethylene vinyl acetate (EVA) at the later phases. Kolmogorov-Smirnov (KS) goodness-of-fit test was used to examine distribution of the data. The compressive strength of EVA-modified concrete was studied by incorporating various concentrations of EVA as an admixture and by testing at ages of 28, 56, 90, 120, 210, and 365 d. An accelerated compressive strength at 3.5 hours was considered as a reference strength on the basis of which all the specified strengths were predicted by means of linear regression fit. Based on the results of KS goodness-of-fit test, it was concluded that KS test statistics value (D) in each case was lower than the critical value 0.521 for a significance level of 0.05, which demonstrated that the data was normally distributed. Based on the results of compressive strength test, it was concluded that the strength of EVA-modified specimens increased at all ages and the optimum dosage of EVA was achieved at 16% concentration. Furthermore, it was concluded that predicted compressive strength values lies within a 6% difference from the actual strength values for all the mixes, which indicates the practicability of the regression equations. This research work may help in understanding the role of EVA as a viable material in polymer-based cement composites.     

Synthesis of Ionic Ultramicroporous Polymers for Selective Separation of Acetylene from Ethylene

The design of highly stable and efficient porous materials is essential for developing breakthrough hydrocarbon separation methods based on physisorption to replace currently used energy-intensive distillation/absorption technologies. Efforts to develop advanced porous materials such as zeolites, coordination frameworks, and organic polymers have met with limited success. Here, a new class of ionic ultramicroporous polymers (IUPs) with high-density inorganic anions and narrowly distributed ultramicroporosity is reported, which are synthesized by a facile free-radical polymerization using branched and amphiphilic ionic compounds as reactive monomers. A covalent and ionic dual-crosslinking strategy is proposed to manipulate the pore structure of amorphous polymers at the ultramicroporous scale. The IUPs exhibit exceptional selectivity (286.1–474.4) for separating acetylene from ethylene along with high thermal and water stability, collaboratively demonstrated by gas adsorption isotherms and experimental breakthrough curves. Modeling studies unveil the specific binding sites for acetylene capture as well as the interconnected ultramicroporosity for size sieving. The porosity-engineering protocol used in this work can also be extended to the design of other ultramicroporous materials for the challenging separation of other key gas constituents.     

乙烯、丙烯中微量水含量的分析

采用便携式微量水分析仪和库仑法微量水分析仪测定了乙烯、丙烯试样中的微量水含量,对试样的传输系统、进样量的控制、液体试样的气化和水标准气体的制备方法进行了改进,优化了测试条件。以低吸附惰性管线和小死体积单进单出的不锈钢减压器为试样传输系统,缩短了测试时间。采用液态烃闪蒸气化取样进样器气化液体试样并准确控制试样的进样量,可避免液体试样渐次气化对水含量测定结果的影响及对采样钢瓶大小的限制。采用渗透管发生器制备水标准气体,可验证分析结果的准确度。采用库仑法微量水分析仪测定水含量时,试样流量选择600 m L/min较适宜,开封保存15 d之内的卡尔·费休试剂对测定结果无影响。采用便携式微量水分析仪测定水含量时,选择试样流量在400~800 m L/min之间较适宜。两种仪器的测量结果相近,稳定性好,准确度高,回收率在102%~107%之间,相对偏差小于10%。     

The Interplay of Modulus,Strength, and Ductility in Adhesive Design Using Biomimetic Polymer Chemistry

High‐performance adhesives require mechanical properties tuned to demands of the surroundings. A mismatch in stiffness between substrate and adhesive leads to stress concentrations and fracture when the bonding is subjected to mechanical load. Balancing material strength versus ductility, as well as considering the relationship between adhesive modulus and substrate modulus, creates stronger joints. However, a detailed understanding of how these properties interplay is lacking. Here, a biomimetic terpolymer is altered systematically to identify regions of optimal bonding. Mechanical properties of these terpolymers are tailored by controlling the amount of a methyl methacrylate stiff monomer versus a similar monomer containing flexible poly(ethylene glycol) chains. Dopamine methacrylamide, the cross‐linking monomer, is a catechol moiety analogous to 3,4‐dihydroxyphenylalanine, a key component in the adhesive proteins of marine mussels. Bulk adhesion of this family of terpolymers is tested on metal and plastic substrates. Incorporating higher amounts of poly(ethylene glycol) into the terpolymer introduces flexibility and ductility. By taking a systematic approach to polymer design, the region in which material strength and ductility are balanced in relation to the substrate modulus is found, thereby yielding the most robust joints.     

Ca-Mg-Al复合氧化物催化尿素与1,2-丙二醇制碳酸丙烯酯

采用共沉淀法制备了系列Ca-Mg-Al复合氧化物催化剂，通过对沉淀剂配比、沉淀液pH值及焙烧温度等制备条件的考察，得到以Na₂CO₃为沉淀剂、pH=9.5、850℃下焙烧4h制备的Ca-Mg-Al催化活性最高。在 n(PG)∶n(urea)=1.5∶1、反应温度为145℃、绝压20kPa、反应时间4h、催化剂用量为尿素质量的5%时，碳酸丙烯酯收率达到84.6%。采用XRF、XRD、NH₃-TPD、SEM及BET对催化剂的组成、晶型及酸性进行了表征，发现随着沉淀剂中Na₂CO₃的含量增加，催化剂中CaO∶MgO的比例增大，碳酸丙烯酯的收率亦升高；经850℃焙烧后，催化剂中存在CaO和MgO两种活性中心，起协同催化作用；随着焙烧温度由700℃升高到850℃，NH₃-TPD脱附曲线向低温方向偏移，且强酸中心NH₃脱附峰面积比由81.14%明显下降为0，中强酸中心NH₃脱附峰面积比由0增加到78.07%，而碳酸丙烯酯收率由68%增加到84.6%，这表明催化剂强酸性位的减少是催化活性增加的主要原因。     

超支化镍系催化剂构效关系及催化乙烯齐聚机理

采用1.0G超支化大分子（1.0G）、3-取代水杨醛和NiCl₂·6H₂O为原料，依次经席夫碱反应和络合反应合成了3种新型具有不同取代基位阻的超支化水杨醛亚胺配体及其镍系催化剂，利用红外光谱（FTIR）、核磁共振氢谱（¹H NMR）、紫外光谱（UV-vis）、电喷雾质谱（ESI-MS）及电感耦合等离子体质谱（ICP-MS）等方法对合成出产物的结构进行表征。考察了配体空间位阻、溶剂种类、助催化剂种类及反应条件对催化乙烯齐聚性能的影响。研究结果表明，配体空间位阻对催化乙烯齐聚性能有较大的影响，当以甲苯为溶剂、甲基铝氧烷（MAO）为助催化剂，在最佳反应条件下，超支化邻苯基水杨醛亚胺镍系催化剂催化乙烯齐聚的活性为2.81×10⁵g/(mol Ni·h)，对高碳烯烃（C₁₀₊）的选择性为34.28%。此外，在超支化水杨醛亚胺镍系催化剂催化性能评价的基础上，对其催化乙烯齐聚的机理进行研究。     

Thermodynamic analysis of ethanol synthesis from hydration of ethylene coupled with a sequential reaction

Coal-based ethanol production by hydration of ethylene is limited by the low equilibrium ethylene conversion at elevated temperature. To improve ethylene conversion, coupling hydration of ethylene with a potential ethanol consumption reaction was analyzed thermodynamically. Five reactions have been attempted and compared: (1) dehydration of ethanol to ethyl ether ({\mathrm{2C}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}\mathrm{OH}\iff{\mathrm{C}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{OC}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{+H}}_{\mathrm{2}}\mathrm{O}), (2) dehydrogenation of ethanol to acetaldehyde ({\mathrm{C}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}\mathrm{OH}\iff {\mathrm{CH}}_{\mathrm{3}}{\mathrm{CHO+H}}_{\mathrm{2}}), (3) esterification of acetic acid with ethanol ({\mathrm{C}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{OH+CH}}_{\mathrm{3}}\mathrm{COOH}\iff {\mathrm{CH}}_{\mathrm{3}}{\mathrm{COOC}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{+H}}_{\mathrm{2}}\mathrm{O}), (4) dehydrogenation of ethanol to ethyl acetate ({\mathrm{2C}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}\mathrm{OH}\iff {\mathrm{CH}}_{\mathrm{3}}{\mathrm{COOC}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{+2H}}_{\mathrm{2}}), and (5) oxidative dehydrogenation of ethanol to ethyl acetate ({\mathrm{2C}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{OH+O}}_{\mathrm{2}}\iff {\mathrm{CH}}_{\mathrm{3}}{\mathrm{COOC}}_{\mathrm{2}}{\mathrm{H}}_{\mathrm{5}}{\mathrm{+2H}}_{\mathrm{2}}\mathrm{O}). The equilibrium constants and equilibrium distributions of the coupled reactions were calculated and the effects of feed composition, temperature and pressure upon the ethylene equilibrium conversion were examined. The results show that dehydrogenation of ethanol to acetaldehyde has little effect on ethylene conversion, whereas for dehydrogenation of ethanol to acetaldehyde and ethyl acetate, ethylene conversion can be improved from 8% to 12.8% and 18.5%, respectively, under conditions of H₂O/C₂H₄ = 2, 10 atm and 300°C. The esterification of acetic acid with ethanol can greatly enhance the ethylene conversion to 22.5%; in particular, ethylene can be actually completely converted to ethyl acetate by coupling oxidative dehydrogenation of ethanol.     

Amine-containing olefin copolymer with CO2-switchable oil absorption and desorption

Global decrease in crude oil resources and frequent crude oil leaks cause the energy crisis and ecological pollution. The absorption and release of leaked crude oil through absorption materials are a necessary process for environmental protection and recycling. In this article, a CO₂-responsive olefin copolymer was obtained by copolymerization of styrene and an amine-containing olefin monomer. The structure of resultant copolymer was characterized by FTIR; thermal properties and CO₂-responsive morphology changes were determined by DSC/TGA and SEM, respectively. Copolymers had certain absorption capacity for toluene with absorption rate up to 180.0%. The absorbed toluene could be released upon CO₂ stimulation with desorption rate up to 84.6%. The CO₂-responsive copolymer could be regenerated through a simple heating process and showed stable absorption–desorption performance even after being recycled for 4 times. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47439.