多业务移动通信系统中的呼叫接入控制

在多业务无线移动通信系统的呼叫接入控制中,不仅要考虑业务之间的优先级,同时也必须考虑切换呼叫的优先级。本文结合可移动边界算法和保护信道策略,提出了一种有效的多业务呼叫接入控制算法。为了方便地分析方案的性能,设计了一个二维的Markov链对方案的性能进行理论上的分析。通过数值分析结果表明,提出的算法同时保证了两种优先级,并提高了系统的性能。1     

无线电车载监测站的信号采集与通讯系统

本系统采用LabVIEW对无线电监测信号进行采集和处理．并开发用户界面。在Delphi平台上运用远程访问服务实现了无线电车载监测站与中心固定站的通讯。LabVIEW主程序对通讯子程序进行调用。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

GPS(NR102K)常见故障与解决方法

GPS硬件由主机和副机两部分组成，本文以Sercel公司生产的NR102K型GPS全球定位系统为例，介绍了其主机和副机在野外施工中的常见故障和解决方法，具有一定的实用性。     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.     

振动筛合金篦条磨损机理及抗磨损技术

分析了山西焦化股份有限公司振动筛合金篦条磨损情况，对合金篦条磨损机理进行了研究，提出控制磨蚀和提高材料耐磨洼的方法。     

VGCR211型调速器在小浪底水电厂的应用

VGCR211型调速器的可编程控制器采用数字化双套冗余配置方式；应用程序由RS232串口写入用户存储器，确保电源消失后程序不会造成任何丢失；输出放大VCAl卡可独立实现对调速器的开度控制功能；转速检测单元采用齿盘测速方式，网频测量取自机端PT；导叶反馈采用角度传感器电气反馈方式。调速器的转速、开度和负荷三种控制模式可任意无扰动切换。在功能实现上，导叶采用关断阀，该阀集开停机阀和紧急停机阀功能于一体，不装事故配压阀。该调速器在小浪底水电厂投运以来其调节性能、可靠性基本达到设计要求，维护工作量较以往传统产品大大减少。     

试油层产液性质的多参数综合判别方法研究

准确地判断储层的产液性质,是试油选层和试油方案优化的重要依据,目前常用的判别方法是基于电测解释结论的多因素经验判别,有较大的人为性和随意性,致使正判率和符合率相对较低,一方面增加了无效的试油工作量,另一方面,增加了漏试油气层的风险.为解决这一问题系统收集和统计了塔里木油田碎屑岩地层反映产液性的录井、测井资料和试油成果资料,通过综合分析对比,提出了预测储层产液性质的新方法--综合权值法.该方法通过一定的规则给电测解释结论、岩心含水迹象、滴水试验、含油饱和度、孔隙度、原油粘度等与产液性相关的因素赋以权值,从而求得综合权值,进而对储层产液性质进行综合判别.综合权值法明显优于单纯的电测解释,使油气水层解释的平均符合率和平均正判率都提高了20%.利用该方法判断储层产液性质具有操作简单、判别率高等优点,对于更合理地优选试油层位和优化试油方案具有重要的实际应用价值.     

变频器在链条炉系统中的应用

本文介绍了链条炉的定义，链条炉应用变频调速的意义，链条炉控制系统的原理，锅炉采用变频调速控制的优点，变频调速的控制方法和逻辑，链条炉采用变频调速装置的节能分析。     

MARK-Ⅳ型气化炉气化剂均布的探讨

通过对炉篦的结构分析 ,并考虑炉内搅拌器的作用 ,结合原料煤的特性 ,提出气化剂均布的原则及方案 ,以改善气化炉操作功效