Controlled Secure Direct Communication Protocol via the Three-Qubit Partially Entangled Set of States

In this paper, we first re-examine the previous protocol of controlled quantum secure direct communication of Zhang et al.’s scheme, which was found insecure under two kinds of attacks, fake entangled particles attack and disentanglement attack. Then, by changing the party of the preparation of cluster states and using unitary operations, we present an improved protocol which can avoid these two kinds of attacks. Moreover, the protocol is proposed using the three-qubit partially entangled set of states. It is more efficient by only using three particles rather than four or even more to transmit one bit secret information. Given our using state is much easier to prepare for multiqubit states and our protocol needs less measurement resource, it makes this protocol more convenient from an applied point of view.     

大型储罐基础非平面倾斜问题的探讨

大型储罐因基础产生非平面倾斜而影响其正常使用的情况在工程中时有发生,文章通过对某油罐工程中基础沉降观测结果的分析,探讨了储罐基础产生非平面倾斜的原因。相邻储罐之间的相互影响、充水预压未达到规范要求以及地基处理措施不当是引起储罐基础非平面倾斜的主要因素。针对相邻储罐间的相互影响,根据现行《石油化工企业设计防火规范》和《石油化工企业钢储罐地基与基础设计规范》的规定,提出以下建议:储罐布置的净距除应满足防火规范规定外,有条件时也应适当考虑对基础沉降的影响,当采用复合地基时,相邻储罐间的净距不宜小于0.6 D;当占地面积成为主要矛盾,储罐间的净距只能限制在防火规范规定的最小范围时,在地基处理时就应采取有效措施,以尽可能减少相邻储罐的相互影响。     

2,4,6‐Trichlorophenol and phenol removal in methanogenic and partially‐aerated methanogenic conditions in a fluidized bed bioreactor

A fluidized bed bioreactor (FBBR) was operated for more than 575 days to remove 2,4,6‐trichlorophenol (TCP) and phenol (Phe) from a synthetic toxic wastewater containing 80 mg L^?1 of TCP and 20 mg L^?1 of Phe under two regimes: Methanogenic (M) and Partially‐Aerated Methanogenic (PAM). The mesophilic, laboratory‐scale FBBR consisted of a glass column (3 L capacity) loaded with 1 L of 1 mm diameter granular activated carbon colonized by an anaerobic consortium. Sucrose (1 g COD L^?1) was used as co‐substrate in the two conditions. The hydraulic residence time was kept constant at 1 day. Both conditions showed similar TCP and Phe removal (99.9 + %); nevertheless, in the Methanogenic regime, the accumulation of 4‐chlorophenol (4CP) up to 16 mg L^?1 and phenol up to 4 mg L^?1 was observed, whereas in PAM conditions 4CP and other intermediates were not detected. The specific methanogenic activity of biomass decreased from 1.01 ± 0.14 in M conditions to 0.19 ± 0.06 mmolCH₄ h^?1 gTKN^?1 in PAM conditions whereas the specific oxygen uptake rate increased from 0.039 ± 0.008 in M conditions to 0.054 ± 0.012 mmolO₂ h^?1 gTKN^?1, which suggested the co‐existence of both methanogenic archaea and aerobic bacteria in the undefined consortium. The advantage of the PAM condition over the M regime is that it provides for the thorough removal of less‐substituted chlorophenols produced by the reductive dehalogenation of TCP rather than the removal of the parent compound itself. Copyright © 2005 Society of Chemical Industry     

填充型UTP5类缆的设计和生产控制

对多线对填充型UTP5类室外干线电缆的性能，设计作了简单介绍，并提出了控制要点。     

钢筋钢纤维增强部分混凝土梁受剪性能试验研究

本文通过钢筋混凝土梁以及在受拉区部分地加入钢纤维的钢筋混凝土梁的试验及理论分析，研究了钢纤维混凝土层厚、钢纤维体积率和剪跨比对钢筋钢纤维增强部分混凝土梁受剪性能的影响，建立了与普遍钢筋混凝土梁受剪承载力计算公式相衔接的钢筋钢纤维增强部分混凝土梁受剪承载力的计算模型和计算公式．     

光阑对部分相干光束模式的影响

本文从 Wolf 的相干理论出发,把部分相干光束的交叉谱密度函数展开为空间完全相干模的叠加:进而讨论光阑对部分相干光束模式的影响。     

乳化炸药混装车水孔爆破的优越性

该文分析了应用袋装炸药装填水孔爆破产生拒爆、"冲天炮"、根底偏高和爆破效果差等问题,然而应用乳化炸药混装车装填水孔可以解决这些问题,并且爆破后具有根底平整、大块率低、毒气少和综合效益高等优点.以三峡永久船闸旁侧泄水箱涵工程和江苏田湾核电站工程为例进行了分析.     

填充HDPE复合材料基体结晶形态的控制因素

本文以HDPE/玻璃微珠和HDPE/CaCO₃体系为研究模型,通过扫描电镜、红外光谱、偏光显微、小角激光散射和材料力学性能实验等方法考察了这两种体系的界面粘结性、填料含量、粒径及试样成型冷却速率等与其材料性能及基体结晶形态变化间的关系。实验结果表明;在复合材料试样成型过程中,因基体树脂冷却收缩而产生的界面应力可干扰基体中球晶的生长环境,应变诱导填料颗粒周围基体树脂的结晶,促使其表面伸展链晶体结构的形成,并由此而明显改变了复合材料的耐热性;复合材料的界面粘结性是产生这种应变诱导作用,并控制异相结晶的关键。     

啮合型同向旋转双螺杆挤出螺槽非充满的熔融理论研究 Ⅱ.模型的求解

根据啮合型同向旋转双螺杆挤出非充满熔融的理论模型，对描述非充满熔融过程的主要物理量：固相高度变化函数、熔融速率及熔融区总长等进行了计算分析，并对有关影响因素进行了讨论。     

Processing of yttria partially stabilized zirconia thermal barrier coatings implementing a high-power laser diode

Several studies have been undertaken recently to adapt yttria partially stabilized zirconia (YPSZ) thermal barrier coating (TBC) characteristics during their manufacturing process. Thermal spraying implementing laser irradiation appears to be a possibility for modifying the coating morphology. This study aims to present the results of in situ (i.e., simultaneous treatment) and a posteriori (i.e., post-treatment) laser treatments implementing a high-power laser diode. In both cases, the coatings underwent atmospheric plasma spraying (APS). Laser irradiation was achieved using a 3 kW, average-power laser diode exhibiting an 848 nm wavelength. Experiments were performed to reach two goals. First, laser post-treatments aimed at building a map of the laser-processing parameter effects on the coating microstructure to estimate the laser-processing parameters, which seem to be suited to the change into in situ coating remelting. Second, in situ coating remelting aimed at quantifying the involved phenomena. In that case, the coating was treated layer by layer as it was manufactured. The input energy effect was studied by varying the scanning velocity (i.e., between 35 and 60 m/min), and consequently the irradiation time (i.e., between 1.8 and 3.1 ms, respectively). Experiments showed that coating thermal conductivity was lowered by more than 20% and that coating resistance to isothermal shocks was increased very significantly.