基于蜻蜓翅脉结构的连续碳纤维增强树脂基复合材料仿生设计与增材制造

以具有轻质高强优异性能的蜻蜓翅脉结构为设计灵感，在分析翅脉网格结构抗冲击原理的基础上，设计了传统和仿生两类对比结构。采用熔融挤出3D打印机成功制备了具有不同结构的连续碳纤维增强聚乳酸复合材料试样，并对不同结构复合材料试样的拉伸性能和抗冲击性能进行了测试和对比分析。研究分析结果表明：由于拉伸力方向上的连续碳纤维含量相对较少，限制了仿生结构复合材料抗拉强度的提高，但仿生结构的平均抗拉强度为传统结构的1.18倍；当仿生结构复合材料试样受到冲击力时，其内部六边形结构的连接角度会发生变化，从而极大消耗冲击能量，同时具有六边形网格结构的连续碳纤维可以有效阻碍裂纹的扩展，因此仿生结构的平均冲击韧性可以达到传统结构的2.46倍；仿生蜻蜓翅脉结构可以显著提高增材制造复合材料的综合力学性能，且对于抗冲击性能的提高具体突出效果。连续碳纤维增强树脂基复合材料的有效可行的仿生蜻蜓翅脉结构设计和增材制造，可极大扩展其在高冲击载荷领域中的相应应用。     

刮板输送机中板仿生耐磨优化试验研究

刮板输送机中板磨损失效已成为输送机运行故障的主要原因之一，为了提高中板耐磨性，基于蜣螂非光滑单元进行了仿生中板设计，以磨损量为响应值，进行了单因素和响应面法优化试验。根据响应面法试验结果得到的因素显著性影响顺序（从高至低）依次为：径向距离，深径比，直径，节距角。基于试验结果建立了磨损量与因素的回归预测模型，经试验对比发现，预测模型与真实试验的相对误差为3.2%。在特定工况（煤散料粒度为6~8 mm、载荷为20 N、刮板链速为0.65 m/s及试验时长为6 600 s）下，当深径比为1.41、直径为0.69 mm、节距角为6.55°和径向距离为4.66 mm时，磨损量最小，仿生中板的耐磨性提高了12.6%。分析其耐磨机理发现，与光滑板相比，仿生板的磨粒磨损及黏着磨损较轻。凹坑分布可破坏持续切削中板表面的煤粒运动状态。中板的仿生优化可为今后刮板输送机的设计提供一定参考。     

超高分子量聚乙烯的辐照效应

通过密度测定和ＤＳＣ热分析，观测了超高分子量聚乙烯的辐射效应。实验结果表明：在吸收剂量０—１．１３ＭＧｙ范围内，密度随吸收剂量的增加而增大，熔化热和熔点也有所增加，特别是在低剂量范围内增加十分明显。以上结果都说明，超高分子量聚乙烯在辐照过程中，结晶在完善或有新的结晶形成     

Development of an Enzymic Time Temperature Integrator for Sterilization Processes Based on Bacillus licheniformis α-amylase at Reduced Water Content

ABSTRACT: The thermal stability of Bacillus licheniformis α-amylase at low moisture content was studied, based on isothermal experiments performed in a temperature range 113 to 125 °C. The thermal inactivation was monitored by measuring the decrease in thermal denaturation enthalpy and/or the decrease in enzymic activity on pnitrophenyl-α-D-maltoheptaoside, or on starch as a substrate. Based on enthalpy readings, an enzymic system with a z-value of 10.4 °C was observed when using a relative humidity of 81% at 4 °C. A theoretical study showed that this system could be used as a Time Temperature Integrator (TTI) to monitor the safety of sterilization processes of numerous food products.     

Immobilized α-amylase from Bacillus licheniformis: a potential enzymic time—temperature integrator for thermal processing

Biphasic and nth-order models were tested as to their usefulness to fit experimental inactivation data of Bacillus licheniformis α-amylase, immobilized on glass beads, and were discussed with respect to their suitability to characterize the considered enzymic system as a time—temperature integrator (TTI) to evaluate heat processes. Both isothermal and non-isothermal inactivation experiments were carried out. Model (kinetic) parameters (rate constant k, activation energy E_A and reaction order n) were estimated using a non-linear regression procedure. The results obtained, especially the activation energy of about 293 kJ mole^–1, indicated a potential use of this system as a TTI for heating processes in the temperature range of 96–108°C.     

Expressing the equivalence of non‐isothermal and isothermal heat sterilization processes

Currently, the sterility of heat‐processed food and pharmaceuticals is assessed in terms of an F₀ value, based on the equivalence of the heat treatment to an isothermal process at a reference temperature. This F₀ value, however, has a meaning if, and only if, the inactivation kinetics of the targeted spores (or cells) follow a first‐order relationship and the temperature dependence of the D value, the reciprocal of the rate constant, is log‐linear. There is growing evidence that these conditions are not satisfied by many spores, including those of Clostridium botulinum and vegetative cells. Consequently, a replacement for the F₀ value is proposed in the form of a momentary equivalent time at the reference temperature based on the actual survival pattern of the spores, which need not be log‐linear. This equivalent time can be calculated together with the theoretical survival ratio in real time, thus enabling an operator to monitor the lethality of ongoing industrial heat processes. The concept is demonstrated with published survival data of C. botulinum, for which the Weibullian and log‐logistic models served as primary and secondary models, respectively. The safety factor according to the proposed method is in the number of added minutes of processing, beyond the theoretical time needed to reduce the survival ratio of the targeted spores or cells to a level that would produce practical (or commercial) sterility. Copyright © 2006 Society of Chemical Industry     

Improving antibacterial,biocompatible, and reusable properties of polyvinyl chloride via the addition of aluminum alkoxides

Global bacterial infections associated with conventional polyvinyl chloride (PVC) medical devices place a heavy burden on healthcare systems and thus it will be desirable if medical devices are made from antimicrobial PVC. There are numerous studies focusing on polymer surface modifications to either leach antimicrobial agents or kill pathogenic microbes upon direct contact. In this work, mannitol fumarate ester-based aluminum metal alkoxide (MFE-Al) additive was developed to confer simultaneously improved antibacterial property and enhanced high temperature sterilization resistance of the resultant PVC. Data obtained confirm that the MFE-Al stabilized PVC sheets significantly inhibit 98% bacterial growth. They also show biocompatibility with cultured H9C2 cardiomyocytes and hemocompatibility in vitro. Dry heat sterilization is generally not suitable for PVC medical wares due to their poor thermal compatibility. Surprisingly, our antimicrobial-biocompatible PVC can maintain stability at 180°C for 90 min. Such a high thermal stability indicates the MFE-Al stabilized PVC can endure 90 cycles of dry-heat sterilization without significant damage. This study may provide a solution to reduce PVC medical waste for a maximum benefit without compromising human health or the environment.     

Bionic Design and Simulation Analysis of Energy-Efficient and Vibration-Damping Walking Mechanism

节能减振步行机构的仿生设计及仿真分析

张锐¹,庞浩¹,何远^1,2,韩佃雷¹,文立阁³,江磊⁴,李建桥¹

（1. 吉林大学 工程仿生教育部重点实验室,长春 130022;

2. 长春长光睿视光电技术有限责任公司,长春 130102;

3. 吉林大学 机械与航天工程学院,长春 130022;

4. 中国北方车辆研究所,北京 100072）

摘要：非洲鸵鸟能以60 km/h的速度持续奔跑30分钟,其后肢结构具有优良的节能、减振性能。为实现腿式机器人高效节能、缓冲减振的腿部机构的设计,根据鸵鸟跗骨间关节的被动回弹特性以及腿部的输出刚度可变特性,结合鸵鸟后肢结构的比例和尺寸,设计出了仿生刚-柔复合腿式机器人单腿结构。并且利用ADAMS软件模拟了仿生机械腿的运动。通过运动仿真分析,研究了内弹簧刚度系数在一定范围内的变化对机身质心垂直加速度以及电机功耗的影响,获得最佳的内弹簧刚度系数为200 N/mm,并进一步验证了内外弹簧机制能够有效地降低机械腿的能耗。仿真结果表明,采用内外弹簧机制能够有效降低电机约72.49%能耗。

关键词：工程仿生;仿生机械腿;被动回弹特性;刚-柔复合结构;节能减振

     

磁悬浮列车造型仿生设计研究

以仿生设计的理论为基础来指导磁悬浮列车造型设计,以期为列车车型概念提供灵感,提高列车造型品质,并满足车体气动性能的基本要求。首先,通过文献研究归纳了国内外以磁悬浮列车为主的轨道列车造型仿生的研究动向;其次,通过案例研究解析典型仿生设计系列车型案例,探究列车仿生对象的应用形式;再次,综合仿生设计与轨道列车设计的方法要素,构建磁悬浮列车仿生设计的一般程序,并基于车体线性趋势的仿生规律,以平鳍旗鱼为仿生对象,设计具有仿生特征的磁悬浮列车概念性设计造型方案;最后,通过初步的仿真模拟,得到该方案的空气阻力系数。通过将本方案与相关案例数据的对比,证明运用仿生设计可以满足磁悬浮列车造型对美学价值和气动性能的要求。     

高分子水处理剂的绿色化研究进展

简要介绍了近年来水处理领域在高分子水处理剂产品及生产工艺方面的绿色化研究进展状况。