Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

直接氯化法合成对硝基氯化苄

介绍了以对硝基甲苯和氯气为原料 ,在催化剂存在下合成对硝基氯化苄的方法 ,考察了催化剂种类、反应温度、溶剂配比等因素对反应的影响 ,优化的反应条件为 :对硝基甲苯用量 1 3 7g,对硝基甲苯 /邻二氯苯 (摩尔比 ) =1∶ 0 .6,w (偶氮二异丁腈 ) =0 .6% ,反应时间 3 h,反应温度 1 60℃ ,产物单程收率大于 65 % ;将反应混合物中未反应的原料分离后 ,以无水乙醇为溶剂结晶纯化 ,物料 /溶剂 (摩尔比 ) =1∶ 1 .5时晶体含量在 99.0 %以上 ,结晶收率达 67     

医用聚氯乙烯材料的表面光接枝改性

研究了在不排氧氛围下 ,紫外光照射 ,以二苯甲酮 (BP)为光引发剂 ,甲基丙烯酸缩水甘油酯(GMA)在医用聚氯乙烯 (PVC)薄膜表面的气相接枝聚合。探讨了反应条件对接枝结果的影响 ,并用正交法指出了影响因素的显著性。用傅立叶红外 (FT- IR)、水接触角作为接枝改性结果的表征。FT- IR谱图表明 GMA已接枝到 PVC膜表面。水接触角由接枝前的 78°下降到 5 4°     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

高温和低张应力引起的非平衡晶界偏聚动力学(Ⅱ)--实验结果的动力学模拟

以文献[1]建立的张应力引起的非平衡晶界偏聚动力学方程模拟了Shinoda T等的磷在钢中的应力时效实验结果和Misra R D K的硫在钢中的应力时效实验结果，模拟结果与实验结果互相吻合。通过模拟发现，张应力使磷-空位复合体以及硫-空位复合体在钢中的扩散系数均增加3个数量级，且磷原子和硫原子的扩散系数分别降低3个和5个数量级。