微制造平台微振动的最优控制

采用混合隔振技术建立了微制造平台隔振系统。该系统以空气弹簧和橡胶层作为被动隔振元件、超磁致伸缩致动器作为主动隔振元件，并采用最优控制理论设计其主动控制器。研究了在不同的性能指标加权阵的情况下，该主动振动控制系统对基础干扰和由微制造设备产生的直接干扰所引起的微制造平台振动的控制效果。研究表明性能指标加权阵对振动控制效果影响非常大。通过大量的仿真实验确定了一组性能指标加权阵，使所设计的主动控制系统能在较宽的频率范围对基础干扰和直接干扰所引起的微制造平台振动进行有效的控制。     

论建立动态勘探目标评价体系的迫切必要性

从国际上通行的油气勘探评价工作重点,中国石油所面临的"已逐步进入一个不断在老区范围内开展精细勘探、在老区范围内开展新区块、新层系勘探以获得主要的储量增长"的新的勘探形势,现有地质研究中各专题研究与具体勘探目标评价脱节等多个方面,论述了在中国石油内部建立一套动态勘探目标评价体系的迫切必要性;并在此基础上阐述了一个完整的动态勘探目标评价体系应包括的主要内容;最后对该体系的建设进行了可行性分析。     

A stochastic model for localized disturbances and its applications

A stochastic model for local disturbances, particularly for a temporal harmonic with random modulations in amplitude and/or phase, is proposed in this paper. Results for the second moment responses of a linear single-degree-of-freedom system to this type of stochastic loading demonstrate a significant change in response characteristics due to a small uncertainty. A local phenomenon may last much longer and resonance may be smeared to a broad range. Integrated with wavelet transform, the proposed approach may be used to model a random process with non-stationary frequency content. Especially, it can be effectively used for Monte Carlo simulation to generate large size of samples that have similar characteristics in time and frequency domains as a pre-selected mother sample has. The technique has a great potential for the case where uncertainty study is warranted but the available samples are limited.     

弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法

提出了一种新的计算弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法，它是一种时域复模态分析方法。利用此方法获得了弹性-粘弹性复合结构在白噪声、滤过白噪声等典型平稳随机激励下随机响应的各阶谱矩的解析表达式，分析了粘弹性对各阶谱矩的影响。此计算方法简便、易用，无论单自由度或多自由度系统均适用，为进一步研究弹性-粘弹性复合结构在随机激励下的可靠性打下良好基础。     

300km/h高速铁路PC槽型梁动力试验研究

介绍北方交通大学与比利时鲁汶大学、布鲁塞尔自由大学、比利时铁路公司合作,在巴黎至布鲁塞尔之间高速铁路线上的Antoing大桥进行的二次高速铁路桥梁动力试验。试验桥梁由跨度50m的多跨预应力混凝土简支槽型梁构成,试验中列车速度达265-310km/h。通过现场试验和实验结果分析,得到了桥梁的频率、振型、阻尼等自振特性,以及桥梁在高速列车作用下的动挠度、梁和桥墩的横向和竖向加速度、橡胶支座的相对位移、梁体的动应变等动力响应特性。试验经验和测试结果对于充实高速铁路桥梁动力分析理论、改进数值分析模型、验证计算结果、提高高速铁路桥梁的动力设计水平、保证行车安全,具有重要的意义。     

具有阻力特性材料的σ_f－σ关系及一种新的阻力曲线测定方法

通过对相变增韧陶瓷及一种可切削玻璃－陶瓷动态疲劳（恒应力速率）试验中高应力速率区断裂应力下降现象的理论分析，发现这种现象与材料的阻力特性（Ｒ－ｃｕｒｖｅ）密切相关。确立的σ_ｆ－σ理论关系能够很好地描述整个应力速率区间内的动态疲劳试验结果。高应力速率区σ_ｆ－σ在双对数坐标下为负斜率直线，直线斜率为（ｍ为阻力曲线ＫＲ＝ｋ（△ａ）~ｍ的指数），断裂主要由材料阻力行为控制；低应力速率区，σ_ｆ－σ在双对数坐标下为正斜率直线，直线斜率为　（ｎ为应力腐蚀指数），断裂主要由材料应力腐蚀行为控制。建立了测定材料阻力特性的一种新方法，分别用这种方法及压痕／弯曲方法对一种可切削玻璃－陶瓷的阻力特性进行了实验测定，两种方法所得结果有很好的一致性。     

Control strategies for reactive batch distillation

A batch reactor may be combined directly with a distillation column by distilling off the light component product in order to increase the reactor temperature or to improve the product yield of an equilibrium reaction. The same amount of the light product should be removed as the amount being formed by the reaction at any time. A linearized model has been developed which describes the process behaviour satisfactorily for control analysis purposes. The controllability of a combined batch reactor/batch distillation column is found to depend strongly on the operating conditions and on the time during the run. In general, controlling only the reactor temperature (one-point bottom control) is difficult since the set-point has to be specified below a maximum value in order to avoid break-through of an intermediate component in the ditillate. This maximum value may be difficult to know a priori. For the example considered in this study, control of both reactor temperature and distillate composition (two-point control) is also found to be difficult due to large interactions in the column. As with one-point bottom control, the reactor temperature has to be specified below a maximum value. However, energy can be saved since the heat duty can be decreased with time. Controlling the temperature on a tray in the column (one-point column control) is found to give good performance for the given process with no loss of reactant and a high reactor temperature, although no direct control of the reactor temperature is obtained.     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

NBR/PP热塑性弹性体研究进展

阐述了NBR／PP共混热塑性弹性体动态硫化胶的国内外研究进展、微观相态结构、性能、应用及展望。     

挠性胶管的阻尼减振机理初探

建立了挠性胶管阻尼耗能的简化模型。以此为基础分析了挠性胶管的阻尼耗能的一般规律,并得出了一些新的结论。