Microstructures and properties of nickel-titanium carbide composites fabricated by laser cladding

In this work, Ni/TiC composites were synthesized by the laser cladding technique (LCT). A scanning electron microscope (SEM), X-ray diffractometer (XRD), microhardness meter, electrochemical workstation, and friction and wear tester examined the microstructure, surface morphology, phase structure, microhardness, wear, and corrosion resistances of the Ni/TiC composites. These results indicated the Ni/40TiC composite contained finer equiaxed crystals than the Ni and Ni/20TiC composites. In addition, numerous TiC particles in the Ni/40TiC composite impeded growth of the nickel crystals, which resulted in the fine microstructure of the Ni/40TiC composite. The Ni, Ni/20TiC, and Ni/40TiC composites exhibited face-centered cubic (f c c) lattices. The average microhardness values of the Ni/20TiC and Ni/40TiC composites were approximately 748 HV and 851 HV, respectively. The Ni/40TiC composite had the lowest friction coefficient (0.43) among all three coatings, and only some shallow scratches appeared on the surface of the Ni/40TiC composite. The corrosion potential (E) of Ni/40TiC exceeded the Ni/20TiC composite, and both were larger than the Ni composite, which indicated the Ni/40TiC composite had outstanding corrosion resistance and the Ni composite had poor corrosion resistance. The corrosion current densities (i) of Ni, Ni/20TiC, and Ni/40TiC composites were 5.912, 4.405, and 3.248 μA/cm², respectively.     

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

基于梯度提升决策树的车轮轮缘厚度磨耗预测

轮对在列车走行过程中起着导向、承受以及传递载荷的作用，其踏面及轮缘磨耗对地铁列车运行安全性和钢轨的寿命都将产生重要影响。根据地铁列车车轮磨耗机理，分析车轮尺寸数据特点，针对轮缘厚度这一型面参数，基于梯度提升决策树算法构建轮缘厚度磨耗预测模型。在该模型的基础上，任意选取某轮对数据进行验证分析，结果表明：基于梯度提升决策树的轮对磨耗预测模型具有较好的预测精度，可预测出1~6个月的轮缘厚度变化趋势范围，预测时间范围较长，可为地铁维保部门对轮对的维修方式由状态修转为预防修提供指导性建议。     

Evolving an Accurate Decision Tree-Based Model for Predicting Carbon Dioxide Solubility in Polymers

Solubility is one of the most indispensable physicochemical properties determining the compatibility of components of a blending system. Research has been focused on the solubility of carbon dioxide in polymers as a significant application of green chemistry. To replace costly and time-consuming experiments, a novel solubility prediction model based on a decision tree, called the stochastic gradient boosting algorithm, was proposed to predict CO₂ solubility in 13 different polymers, based on 515 published experimental data lines. The results indicate that the proposed ensemble model is an effective method for predicting the CO₂ solubility in various polymers, with highly satisfactory performance and high efficiency. It produces more accurate outputs than other methods such as machine learning schemes and an equation of state approach.     

Gradient-based recursive parameter estimation for a periodically nonuniformly sampled-data Hammerstein–Wiener system based on the key-term separation

The identification of the Hammerstein–Wiener (H-W) systems based on the nonuniform input–output dataset remains a challenging problem. This article studies the identification problem of a periodically nonuniformly sampled-data H-W system. In addition, the product terms of the parameters in the H-W system are inevitable. In order to solve the problem, the key-term separation is applied and two algorithms are proposed. One is the key-term-based forgetting factor stochastic gradient (KT-FFSG) algorithm based on the gradient search. The other is the key-term-based hierarchical forgetting factor stochastic gradient (KT-HFFSG) algorithm. Compared with the KT-FFSG algorithm, the KT-HFFSG algorithm gives more accurate estimates. The simulation results indicate that the proposed algorithms are effective.     

一种基于小字典不对等语料的跨语言词嵌入方法

双语词嵌入通常采用从源语言空间到目标语言空间映射,通过源语言映射嵌入到目标语言空间的最小距离线性变换实现跨语言词嵌入。然而大型的平行语料难以获得,词嵌入的准确率难以提高。针对语料数量不对等、双语语料稀缺情况下的跨语言词嵌入问题,该文提出一种基于小字典不对等语料的跨语言词嵌入方法,首先对单语词向量进行归一化,对小字典词对正交最优线性变换求得梯度下降初始值,然后通过对大型源语言(英语)语料进行聚类,借助小字典找到与每一聚类簇相对应的源语言词,取聚类得到的每一簇词向量均值和源语言与目标语言对应的词向量均值,建立新的双语词向量对应关系,将新建立的双语词向量扩展到小字典中,使得小字典得以泛化和扩展。最后,利用泛化扩展后的字典对跨语言词嵌入映射模型进行梯度下降求得最优值。在英语—意大利语、德语和芬兰语上进行了实验验证,实验结果证明该文方法可以在跨语言词嵌入中减少梯度下降迭代次数,减少训练时间,同时在跨语言词嵌入上表现出较好的正确率。     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

PETROLEUM POTENTIAL, THERMAL MATURITY AND THE OIL WINDOW OF OIL SHALES AND COALS IN CENOZOIC RIFT BASINS, CENTRAL AND NORTHERN THAILAND

Oil shales and coals occur in Cenozoic rift basins in central and northern Thailand. Thermally immature outcrops of these rocks may constitute analogues for source rocks which have generated oil in several of these rift basins. A total of 56 oil shale and coal samples were collected from eight different basins and analysed in detail in this study. The samples were analysed for their content of total organic carbon (TOC) and elemental composition. Source rock quality was determined by Rock‐Eval pyrolysis. Reflected light microscopy was used to analyse the organic matter (maceral) composition of the rocks, and the thermal maturity was determined by vitrinite reflectance (VR) measurements. In addition to the 56 samples, VR measurements were carried out in three wells from two oil‐producing basins and VR gradients were constructed. Rock‐Eval screening data from one of the wells is also presented. The oil shales were deposited in freshwater (to brackish) lakes with a high preservation potential (TOC contents up to 44.18 wt%). They contain abundant lamalginite and principally algal‐derived fluorescing amorphous organic matter followed by liptodetrinite and telalginite (Botryococcus‐type). Huminite may be present in subordinate amounts. The coals are completely dominated by huminite and were formed in freshwater mires. VR values from 0.38 to 0.47%R_o show that the exposed coals are thermally immature. VR values from the associated oil shales are suppressed by 0.11 to 0.28%R_o. The oil shales have H/C ratios >1.43, and Hydrogen Index (HI) values are generally >400 mg HC/g TOC and may reach 704 mg HC/ gTOC. In general, the coals have H/C ratios between about 0.80 and 0.90, and the HI values vary considerably from approximately 50 to 300 mg HC/gTOC. The HI_max of the coals, which represent the true source rock potential, range from ～160 to 310 mg HC/g TOC indicating a potential for oil/gas and oil generation. The steep VR curves from the oil‐producing basins reflect high geothermal gradients of ～62°C/km and ～92°C/km. The depth to the top oil window for the oil shales at a VR of ～0.70%R_o is determined to be between ～1100 m and 1800 m depending on the geothermal gradient. The kerogen composition of the oil shales and the high geothermal gradients result in narrow oil windows, possibly spanning only ～300 to 400 m in the warmest basins. The effective oil window of the coals is estimated to start from ～0.82 to 0.98%R_o and burial depths of ～1300 to 1400 m (～92°C/km) and ～2100 to 2300 m (～62°C/km) are necessary for efficient oil expulsion to occur.     

重力坝模型的尺寸效应

利用两个不同比尺预制缝重力坝模型的试验成果，以有限元富集技术进行非线性断裂分析，建立了极限承载力和长度比尺的确定性尺寸效应公式。混凝土重力坝的断裂尺寸效应满足指数衰减关系，用三次指数衰减公式可以准确地预测原型的极限承载力。断裂过程区的相对长度是引起模型试验尺寸效应的主要原因。数值计算结果表明，断裂过程区相对长度不仅是与材料有关的参数，能否充分发展还取决于结构尺寸和几何形状；断裂过程区相对长度的尺寸效应不同于统计尺寸效应和断裂参数尺寸效应，具有尺寸范围效应。断裂过程区相对长度在小试件、大试件和相对无穷大试件的发展程度不同。