Structural dependence of microwave dielectric properties of spinel structured Mg2(Ti1-xSnx)O4 solid solutions: Crystal structure refinement,Raman spectra study and complex chemical bond theory

Mg₂(Ti_1-xSn_x)O₄ (x?=?0–1) ceramics were prepared through conventional solid-state method. This paper focused on the dependence of microwave dielectric properties on crystal structural characteristics via crystal structure refinement, Raman spectra study and complex chemical bond theory. XRD spectrums delineated the phase information of a spinel structure, and structural characteristic of these compositions were achieved with the help of Rietveld refinements. Raman spectrums were used to depict the correlations between vibrational phonon modes and dielectric properties. The variation of permittivity is ascribed to the Mg₂(Ti_1-xSn_x)O₄ average bond covalency. The relationship among the B-site octahedral bond energy, tetrahedral bond energy and temperature coefficient are discussed by defining on the change rate of bond energy and the contribution rate of octahedral bond energy. The quality factor is affected by systematic total lattice energy, and the research of XPS patterns illustrated that oxygen vacancies can be effectively restrained in rich oxygen sintering process. Obviously, the microwave dielectric properties of Mg₂(Ti_1-xSn_x)O₄ compounds were obtained (${\epsilon }_r$= 12.18, $Q\times f$?=?170,130?GHz, ${\tau }_f$?=??53.1?ppm/°C, x?=?0.2).     

Optimised phase compositions and improved microwave dielectric properties based on calcium tin silicates

The Ca_(1+2y)Sn_(1-x)Si_(1+y)O_(5-2x+4y) low-permittivity microwave dielectric ceramics were prepared through solid-state reaction at 1350–1450 °C for 5 h. The relations between microwave dielectric properties and phase compositions for non-stoichiometric Ca_(1+2y)Sn_(1-x)Si_(1+y)O_(5-2x+4y) ceramics have been investigated. A single CaSnSiO₅ phase with abnormally positive temperature coefficient of resonant frequency (τ_f = + 62.5 ppm/°C) was synthesised at 1450 °C. This composition was an effective τ_f compensator of CaSiO₃ and Ca₃SnSi₂O₉ phases with typically negative τ_f value. The CaSiO₃ second phase was related to the Sn deficiency in the CaSn_(1-x)SiO_(5-2x) (0 < x < 1.0) composition, whereas the Ca₃SnSi₂O₉ second phase was obtained by controlling the Ca:Sn:Si ratios on the basis of the Ca_(1+2y)SnSi_(1+y)O_(5+4y) (0 < y < 1.0) composition. A promising low-permittivity millimetre-wave ceramic with most excellent microwave dielectric properties (ε_r = 10.2, Q×f = 81,000 GHz and τ_f = −4.8 ppm/°C) was produced from the Ca_(1+2y)SnSi_(1+y)O_(5+4y) (y = 0.4) ceramic.     

Sol-Gel Preparation and Luminescence Properties of BaMgAl10O17∶Eu2+ Phosphors

The synthesis of BaMgAl10O17∶ Eu2 (BAM) phosphors using the sol-gel method and their luminescence properties were reported. The blue-light emitting BAM was synthesized using citric acid and ethylene glycol as chelating materials. Emission of blue-light was obtained from these phosphors. The luminescent intensity increases as the temperature of heat treatment is increased. This study investigated the effects of the molar ratio of ethylene glycol to citric acid (Φ value), with respect to the phase formation and luminescence properties of BAM. The variation of the Φ value resulted in the change of the sol-gel reaction mechanism and the microstructures of the resultant powders. An increase in Φ value leads to an increase in the rate of BAM phase formation. The photoluminescent intensity of the prepared phosphors increases with heating temperatures because of enhanced crystallization.     

Effects of Rare Earths on Toughness of 31Mn2SiRE Wear-Resistance Cast Steel

The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.     

强捻棉纱针织产品的性能研究

通过对强捻棉纱针织产品进行服用性能测试，得出强捻纱织物具有良好的服用性能。     

6种金属材料在典型工业大气中的腐蚀规律

选取具有代表性的碳钢、不锈钢、镀锌碳钢、铝、钛和铜挂片,在某企业不同部位投放后进行为期半年的大气腐蚀试验,得出了在半年期中的腐蚀规律。在此基础上,对每种金属材料的腐蚀特点进行总结,并对大气腐蚀的各种影响因素进行分析,提出了行之有效的防护措施。     

一种PD雷达动目标模拟与微波测控系统

介绍了一种基于PC／104总线，具有GPIB程控功能，采用无内部微波源体制，通过在雷达载频上调制多普勒频率模型目标速度信息，延迟雷达发射机触发脉冲模拟目标距离信息并具有微波功率精确定标与衰减功能的PD雷达动目标模拟与微波测控系统。     

不锈钢管道坡口加工的新方法

对于不锈钢管及合金钢管坡口的加工,采用以往的加工方法切割出来的坡口一般参差不平、比较粗糙,难于打磨平整。使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段,改善了不锈钢管及合金钢管的坡口加工效果,使加工出来的坡口像碳钢管一样平整,更加容易打磨组焊。文章介绍了这一新方法所用的设备、材料、切割原理以及操作过程。