一种基于三次样条函数求离子浓度的自动算法

本文提出了一种用三次样条函数模拟双次标准加入法测量方程，直接求解离子浓度的自动算法。比较了三咱不同边界条件下用要池数计算离子浓度的结果。造出节点区间两极端点的二阶导数为零时的三次样条函数为最佳模拟函数。并讨论了该方法在实际分析中误差的来源及消除办法。经对一系列文献数据的验算对比，表明本法完全可代替传统的迭代法和查图法，且能方便地设置在智能化的电位分析系统中。     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

局部设有钢筋砼电梯井墙的设计探讨

本文就局部设有钢筋砼电梯井的工程计算及理论分析，阐明分析了少墙的框剪结构的设计及注意问题。     

武山铜矿主井系统延深改造及效果浅析

武山铜矿主井延深时根据新的采、选工艺要求，在前期工程的基础上，对其箕斗提升系统进行改造，增设坑内破碎。针对该矿特粘的矿石性质和前期工程遗留问题，在具体设计和实施过程中采取特别措施保证系统通畅和安全并注意节省投资。同时对尚存在的问题也提出了新的思考。     

四川南桠河一期工程姚河坝水电斜井开挖施工技术浅论

以姚河坝水电站引水隧洞50°倾角、长度为194.734m的斜井开挖为实例,从施工测量、开挖方法、通风防尘、临时支护斜井及安全施工等方面探讨长洞身、大倾角斜井在无爬罐条件下的人工开挖方法.     

单膛石灰竖窑的改造

我厂竖窑容积为250m^3，设计利用系数为0．85t/(m^3．d)。随烧结产量的不断增加，石灰产量已不能满足烧结生产的需要。为了提高石灰产量，进行了扩容改造，容积由原来250m^3增加到298m^3，并针对目前生产实际提出下一步改造设想。     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。     

用保形样条方法求解非定常对流扩散方程

在欧拉-拉格朗日分裂方法的基础上,本文发展了一种固定网格上的欧拉-拉格朗日分裂方法.保形样条方法(SPSM)被用来解决倒特征线插值问题.通过求解几个有精确解的例子,说明SPSM方法的解是单调无振荡的,并且数值耗散也是比较小的.     

符号运算在求解车辆传动系扭振中的应用

介绍符号运算方法在用拉普拉斯变换方法求解车辆传动系扭振过程中的作用．针对弹性联轴器的匹配计算，给出了具体求解实例．实践表明，与传统的纯数值计算方法相比，符号运算方法可以方便准确地处理车辆传动系统扭振分析中的非线性等复杂问题，具有推广应用价值．     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.