Anaerobic co-digestion of food waste and FOG with sewage sludge – realising its potential in Ireland

The severe environmental pollution in many countries is caused by indiscriminate discharge of large quantities of food waste (FW), fat oil and grease (FOG) and sewage sludge (SS) to the environment. There are many possible treatment routes, but anaerobic digestion (AD) is now well accepted for treating several kinds of organic wastes. But AD of FW alone presents some operational challenges because of substrates and variability. Anaerobic co-digestion of two or more substrates is better than single substrate digestion. This can use a plant’s unused capacity, in line with the trend to renewable energy. Co-digestion technology, although well established in many European countries, is still in its infancy in Ireland. There are problems with different regulatory arrangements. They should be resolved. The paper reviews anaerobic co-digestion technology is reviewed, with special focus on possible application in Ireland.     

Reduction of waste biosolids by RAS-ozonation: Model validation and sensitivity analysis for biosolids reduction and nitrification

Biosolids reduction model by return activated sludge ozonation was validated by simulating nitrification data compiled from our pilot-scale and the literature studies. Then, a global sensitivity analysis (GSA) was performed to identify influential and non-influential parameters for biosolids reduction efficiency, change in specific nitrification activity (SNA), and alteration to expected nitrification stability. In general, the model outputs were sensitive to operational and ozone reaction parameters, but not to biochemical parameters. For operational parameters, mainly temperature and initial solids retention time (SRT) influenced all model outputs. For biosolids reduction, increase in the degradability of the influent COD decreased the reduction efficiency. For SNA, the changes were highly dependent on the influent TKN/COD ratio. Our findings also imply that the stability of the nitrification process in ozonated systems should be enhanced at constant MLVSS for warm temperatures, but could be reduced at temperatures below 12 °C and aerated SRTs below 10 days.     

Chemically modified organic/inorganic nanoporous composite particles for the adsorption of reactive black 5 from aqueous solution

In the present work, we report a chemically modified polyacrylamide/silica nanoporous composite adsorbent for the removal of reactive black 5 (RB5) azo dye from aqueous solutions. The composite adsorbent was synthesized in a packed bed and modified by ethylenediamine (EDA). The adsorbent was characterized by Fourier transformation infrared (FT-IR), thermogravimetric analysis (TGA), thermoporometry, Brunauer, Emmett and Teller (BET) method and scanning electron microscopy (SEM). Mechanical stability of the adsorbent was examined in a packed bed by following the back-pressure of the column. Pore diameter of the composite adsorbent in dry and wet states was estimated to be about 18.71 nm and 12.61 nm, respectively. Adsorption experiments were performed in batch mode and effect of various operational parameters on the adsorption capability of the adsorbent was studied systematically. The maximum adsorption capacity of the modified composites was found to be 454.5 mg RB5/g of adsorbent. The equilibrium data were analyzed by Langmuir, Freundlich, Sips, BET and Redlich–Peterson isotherm models and found to fit well to the BET isotherm. The data kinetically followed the pseudo-second-order model. High adsorption capacity, fast removal mechanism, and good mechanical stability are three advantages of the presented composite for the removal of RB5.     

黑匣子高温测试仪的开发

采用物质的相变吸热原理，可以将高温环境传人保温箱的热量重新排回至高温环境，有效地提高了保温箱的抗高温能力，并对保温箱的隔热性能做了简单的理论推算和测温反向试验。温度测试仪选用超低功耗CPU，具有体积小、耗电少的优点，使黑匣子高温测试仪在运行过程中具有很好的安全可靠性。     

用于制备膨体颗粒调剖剂的含油污泥除油技术研究

利用含油污泥制备膨体颗粒调剖剂用于调剖堵水是一种新的污泥资源化技术，研究了含油污泥的预处理方法，尤其是除油技术。分别使用热水酸洗、热水酸洗／除油剂对污泥进行了除油试验，并以干泥含油率为指标考察了pH值、水与泥质量比、除油剂用量对除油效果的影响。试验结果表明，在水与泥质量比为2．0、pH值为6．0、45℃条件下，用矿化水热水酸洗可使干泥含油率从31．5％降至19．4％。同样条件下，除油剂用量为40．0mg／L时，热水酸洗／除油剂处理能使干泥含油率进一步降至11．2％。聚合试验结果表明，经热水酸洗／除油剂处理后的污泥能够聚合得到胶块强度高、膨胀倍数高的膨体颗粒调剖剂。     

Pilot Plant Study of Simultaneous Sewage Sludge Digestion and Metal Leaching

This research is related to a preindustrial pilot scale study of the performance of the simultaneous sewage sludge digestion and metal leaching (SSDML) process for decontamination and stabilization of sewage sludge. Ten batch tests were carried out in two 4?m3 bioreactors under various conditions of operation. Results indicated that the addition of 1.0 to 1.5?g?S0/L, which is the equivalent of approximately 30 to 50?kg?S0 per tons dry sludge, is sufficient to obtain conditions of acidity (pH<2.5) and oxido-reduction potential greater than 500 mV necessary for an effective solubilization of toxic metals. The final average of metal solubilization in the output sludge during the SSDML process varied in the following ranges: 25–78% Cd, 9–32% Cr, 48–100% Cu, 77–99% Mn, 15–53% Ni, 12–47% Pb, and 66–100% Zn. The N, P, and K contents were also preserved in the decontaminated sludge. Moreover, the use of low concentrations of elemental sulfur makes it possible to obtain decontaminated sludge with a low total sulfur content (1.4–1.5% S) compatible with agricultural use. The suspended solids removal calculated for the SSDML process was slightly lower, (2.5±0.4)% volatile suspended solids per day, than those reached using standard aerobic digestion. Finally, the SSDML process was found to be effective in removing bad odors and in the destruction (99–100%) of indicator bacteria.     

无钴黑色陶瓷颜料中铬含量测定的新方法

本文以盐酸羟胺作还原剂,研究了三价铬与二甲酚橙的显色反应,结果发现Cr3 在0～80滋g/50ml范围内,其吸光度与Cr3 含量成正比相关,用于无钴黑色陶瓷颜料中铬含量的测定,作出了回归方程,且进行了显著性检验,获得了理想的结果。