Evolution of the structure and mechanical performance of Cansas-II SiC fibres after thermal treatment

Herein, an in-depth analysis of the effect of heat treatment at temperatures between 900 and 1500 °C under an Ar atmosphere on the structure as well as strength of Cansas-II SiC fibres was presented. The untreated fibres are composed of β-SiC grains, free carbon layers, as well as a small amount of an amorphous SiC_xO_y phase. As the heat-treatment temperature was increased to 1400 °C, a significant growth of the β-SiC grains and free carbon layers occurred along with the decomposition of the SiC_xO_y phase. Moreover, owing to the decomposition of the SiC_xO_y phase, some nanopores formed on the fibre surface upon heating at 1500 °C. The mean strength of the Cansas-II fibres decreased progressively from 2.78 to 1.20 GPa with an increase in the heat-treatment temperature. The degradation of the fibre strength can be attributed to the growth of critical defects, β-SiC grains, as well as the residual tensile stress.     

Synthesis and characterization of superoleophobic fumed alumina nanocomposite coated via the sol-gel process onto ceramic-based hollow fibre membrane for oil-water separation

Oily wastewater treatment is a global challenge due to the substantial amount of effluent resulted from many industrial and domestic activities. To overcome the challenge of using existing treatment approach and fouling, superoleophobic coatings were fabricated. In this study, a superoleophobic membrane surface was obtained using the sol-gel technique with perfluorooctanoate (PFO), poly (diallyl dimethylammonium chloride) (PDADMAC), and nanoparticles as complex-polymer nanocomposites. The effects of coating cycles on the surface structure, chemical properties, surface chemistry, and oleophobicity of the surface were examined using field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and oil contact angle measurement. The results showed that the coated layer successfully adhered to the substrate surface. However, the chemical stability with respect to oil contact angle (OCA) revealed a decline at pH 7 and pH 9 and maintained stability at pH 3. Besides, oil flux at 63.0 L/m². h was achieved for PDADMAC-Al₂O₃/44 wt% PFO and the highest separation efficiency of 98% was obtained. Furthermore, the oil rejection decreases as the oil concentration increases from 1 to 3 g/L. OCA of 155° was obtained after 5 coating cycles. Apart from mitigating substrate fouling, the superoleophobic and superhydrophilic coating can be applied to a ceramic-based hollow fibre membrane and efficiently used for the separation of oil from oily wastewater.     

The effect of rice bran on physicochemical,textural and glycaemic properties of ready-to-eat extruded corn snacks

In this work, corn extruded snack products were enriched with rice bran (RB) at 10% and 15%. A co-rotating twin-screw extruder was used with a feed moisture content of 16 g 100 g⁻¹, a screw speed of 240 r.p.m. and four heating sections of the barrel (100, 140, 150 and 150 °C). The impact of RB inclusion on nutritional profile, starch digestion, physicochemical and textural properties of snack products was evaluated. RB-enriched extrudates showed a lower specific volume and hardness and higher crispness than control. RB at 15% gave a water-holding capacity lower than control. Rheology of extrudate dispersions indicated an increase in elastic interactions and solid-like behaviour with RB supplementation. Differences in rheological properties resulted in attenuation of predictive glycaemic response for RB-enriched snacks.     

Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

Toughness enhancement and equivalent initial fracture toughness of cementitious composite reinforced with aligned steel fibres

Based on theoretical analysis and numerical simulation, the impact of steel fibres on the stress intensity factor (SIF) at the crack tip for cementitious composite was studied. The enhanced toughness of steel fibre reinforced cementitious composite (SFRC) in resisting cracks was explained by the decrement of SIF caused by steel fibre inclusions at the crack tip of the composite. The equivalent initial fracture toughness was used to characterize the crack initiation of SFRC. A simplified method for determining the of SFRC was proposed based on a linear regression method. Fracture tests were conducted on three‐point bending notched beams with different steel fibre volume fractions and specimen sizes to study the crack initiation behaviour of aligned steel fibre reinforced cementitious composite (ASFRC). of ASFRC was calculated, and the size effect of was analysed. The results showed that slightly increased with the steel fibre volume fraction and gradually became stable. For the tested specimens, whose heights varied between 40 and 100 mm, the specimen size had little impact on the .     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

The use of bio-diesel based additive as rheology improver and pour point depressant of Nigerian waxy crude

The chemical method has proved to be the most effective mitigating method of wax deposition in petroleum system as it deals with the root cause of wax formation. Most of the commercial chemicals in the industry are very expensive and toxic. This paper aims the use of biodiesel based additives for improving the rheological behavior and pour points of waxy crude from Nigeria field. The biodiesels derived additives gave better performance than the commercial chemical and the seed oils as greatly improvement in rheology and pour point values of the waxy crude were observed     

Occurrence and distribution of dibenzofurans and benzo[b]naphthofurans in the crude oils from the Northern and offshore Niger Delta basin,Nigeria

The occurrence and distributions of dibenzofurans (DBFs) and benzo[b]naphthofurans were investigated in crude oils from Niger Delta, Nigeria, by gas chromatography-mass spectrometry-mass spectrometry. The distribution of DBFs was characterized by the predominance of C₂-dibenzofurans. 4-Methyldibenzofuran was the most abundant among the methyldibenzofurans isomers while dimethyldibenzofuran-2 (DMDBF-2), ethyldibenzofuran-1, DMDBF-3, and DMDBF-6 occurred in higher amounts when compared with other DMDBFs. Among the benzonaphthofurans, the abundance of benzo[b]naphtho[2,1-d]furan was higher than other isomers. The DBFs distributions in the oils were not affected by source facies and depositional environments. However, the DBFs concentrations increased with increasing maturity in oils from ADL and MJO oilfields.     

Neutral axis depth and moment redistribution in FRP and steel reinforced concrete continuous beams

The neutral axis depth is considered the best parameter for quantifying the moment redistribution in continuous concrete beams, as exemplified in various design codes worldwide. It is therefore important to well understand the variation of neutral axis depth against moment redistribution. This paper describes a theoretical investigation into the neutral axis depth and moment redistribution in concrete beams reinforced with fibre reinforced polymer (FRP) and steel bars. A finite element model has been developed. The model predictions are in favourable agreement with experimental results. Three types of reinforcement are considered, namely, glass fibre, carbon fibre and steel. Various levels of reinforcement ratio are used for a parametric evaluation. The results indicate that FRP reinforced concrete continuous beams exhibit significantly different response characteristics regarding the moment redistribution and variation of neutral axis depth from those of steel reinforced ones. In addition, it is found that the code recommendations are generally unsafe for calculating the permissible moment redistribution in FRP reinforced concrete beams, but the neglect of redistribution in such beams may be overconservative.