Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

稀土石膏常压酸化法制备硫酸钙晶须的研究

以含稀土的石膏为原料运用常压酸化法合成硫酸钙晶须,探讨了不同工艺条件对生成的硫酸钙晶须形貌的影响,同时还考察了晶型助长剂的种类和晶型助长剂的含量对硫酸钙晶须生长的影响,利用SEM和XRD分别对硫酸钙晶须的表面形貌、物相特征做了表征分析。实验得到制备硫酸钙晶须的最佳的反应条件：稀土石膏质量浓度为0.22 g/mL、反应时间为25 min、盐酸浓度为2.8 mol/L、反应温度为70 ℃、陈化时间为4 h,在此条件下合成的硫酸钙晶须平均长度为61 μm,平均长径比为30.5;通过对比实验选出了CuCl₂作为促进硫酸钙晶须生长的助长剂,在添加5%（质量分数）的CuCl₂的情况下可使硫酸钙晶须长径比从30.5增至41,长度从61 μm增至81 μm。     

T-ZnO晶须增强环氧树脂复合材料的力学行为

研究了以四脚状氧化锌（T-ZnO）晶须为增强剂，环氧树脂复合材料的力学行为。结果表明，由具有三维空间结构的T-ZnO晶须为增强剂所制备的环氧树脂复合材料具有各向同性的力学性能，T-ZnO晶须填加质量分数为6%时，就可使材料的力学性能改善；拉伸强度提高到169%，拉伸功几乎提高了100%，冲击强度提高到300%，抗弯的断裂功提高到158%，而压缩强度略有下降。     

晶须取向对SiCw/6061Al复合材料热压缩变形行为的影响

采用SEM 和 Magiscan-2A 图像分析系统研究了晶须取向对SiCw/6061Al复合材料在300℃压缩变形行为的影响.结果表明:晶须取向影响着晶须折断程度和转动角度; 随着晶须取向角的增加,晶须转动和折断行为所导致的软化效果下降.同时晶须取向也影响复合材料的热压缩应力-应变曲线的形状.在热压缩变形过程中,晶须取向角为0°和30°的复合材料表现出明显应变软化现象, 晶须取向角为45°的复合材料无明显软化现象.晶须取向角为90℃的复合材料表现出应变硬化现象.     

Electromigration-induced damage in bamboo Al interconnects

Depletion and hillock formation were examined in-situ in a scanning electron microscope (SEM) during electromigration of bamboo Al interconnect segments. Hillocks formed directly at the anode ends of the segments by epitaxial addition of Al at the bottom Al/TiN interface. Depletion occurred nonuniformly from the cathode end and stopped once the distance between the leading void and the hillock reached the critical length for electromigration at the given current density. A modified equation for the drift velocity is proposed, which includes the effect of nonuniform depletion and predicts that interconnects with nonuniform depletion are more reliable than those with uniform depletion.     

SiC（w）／TZP＋mullite陶瓷复合材料界面和组成设计与力学性能

本文从理论上分析了ＳｉＣ（ｗ）ＴＺＰ＋ｍｕｌｌｉｔｅ（ｐ）复合材料界面残余热应力及其在基质内的分布规律。提出在ＳｉＣ（ｗ）表面涂复Ａｌ２Ｏ３和在ＰＺＴ中加入ｍｕｌｌｉｔｅ（ｐ）联合作用来降低晶须／基质界面残余热应力的界面设计方案，导出ＳｉＣ（ｗ）和ｍｕｌｌｉｔｅ（ｐ）协同补强ＰＺＴ的匹配条件。制备了ＳｉＣ（ｗ）／ＴＺＰ＋ｍｕｌｌｉｔｅ（ｐ）复合材料并了ＳｉＣ（ｗ）表面涂层Ａｌ２Ｏ３厚度和ＳｉＣ（ｗ     

硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。     

TiB2和SiCW对Al2O3陶瓷材料高温摩擦磨损特性的影响

研究了Ａｌ２Ｏ３、Ａｌ２ｏ３／ＴｉＢ２和Ａｌ２Ｏ３／ＴｉＢ２／ＳｉＣＷ三处陶瓷材料在不同条件下的擦靡损特性。结果表明：三种陶瓷材料与硬质合金摩擦副的摩擦系数随温度温度的增加有不同的变化规律，摩擦表面的Ｘ射线衍射分析表明，摩擦系数的变化与陶瓷物膜的和结构有关，在高温下Ａｌ２Ｏ３／ＴｉＢ２陶瓷材料摩擦表面形成了具有优良的高温润性的ＴｉＯ２氧化膜，因而ＴｉＢ２的加入明显改善了Ａｌ２Ｏ３陶瓷材料 摩擦磨损     

树脂热解炭制备碳化硅晶须

用自制的配合醛树脂热解和炭源，用ＳＩＯ２超细汾作原，根据碳热还原原理，利用常规加热和微波加热两种方式，分别制备了直径在纳米级的ＳｉＣ晶须，Ｘ射线衍射、透射电检测结果表明：制备工艺和条件对ＳｉＣ晶须的性质有较大的影响。