Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

减振器在自导系统结构设计中的应用

通过对减振器结构设计的理论分析，建立了减振器的数学模型，同时通过设计的模拟装置对减振效果进行了实测，效果良好。     

30.4 nm光电成像系统分辨率的初步实验研究

本文基于微通道板MCP(Microchannel Plate)探测器件设计一套成像系统，用于对波长为30．4nm的极紫外EUV(Extreme Ultraviolet)光进行成像．结果获得了一宽度为3mm的狭缝的像，实验测得490μm的成像系统的空间分辨率，并分析了影响系统分辨率的各种因素及为提高系统分辨率所应采取的措施．     

垂直管吸收器内泡式吸收过程的数值研究

建立垂直管吸收器管内泡式吸收过程中传热传质的数学物理模型，对其泡式吸收过程进行数值研究，获得泡式吸收方式的一些传热传质特性，为吸收器的优化设计提供一定理论指导。     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

有限周期梁用动力消振器抑振的特性

本文用弯曲波方法导出了多支承梁加动力消振器位移响应的普遍表达式。理论分析发现了周期结构用动力消振器抑制振动的一些新特性：（１）仅用一个动力消振器可抑制周期结构对应传递频带内的一组共振峰。被抑制的共振峰的数量与跨距的数量和消振器的布置位置有关；（２）动力消振器调谐频率与对应传递频带的第一个共振频率相关联。当动力消振器与作用在梁上的外载荷作用在同一点时，最佳调谐频率比总是大于１，否则最佳调谐频率比小于１。     

利用高酸值餐饮废油脂制备生物柴油

以高酸值餐饮废油脂为原料,在酯化反应后再经两步酯交换反应制备生物柴油。在酯化反应中添加吸水剂可降低油脂的酸值,经一次酯化反应即可将油脂的酸值降至2m g/g左右,满足酯交换反应的要求。考察了酯化反应中吸水剂的添加方式、种类及其用量对酯化反应的影响,以及酯交换催化剂的种类及用量对脂肪酸甲酯(FAME)收率和产物组成的影响。实验结果表明,以凹凸棒土为吸水剂(用量为餐饮废油脂中游离脂肪酸质量的3%),且在酯化反应30m in时加入,酯化效果较好;以质量比为1∶1的NaOH和KOH混合物为催化剂进行两步酯交换反应时,催化剂的最佳用量依次为1.00%和0.75%(质量分数,基于油脂的质量),FAME收率最高达到96.33%。     

天然彩色棉产品抗紫外线处理的探讨

介绍了天然彩色棉的应用现状以及对其进行抗紫外线处理的现实意义，探讨了抗紫外线处理的方法和检测手段，并结合初步的实验提出在天然彩色棉产品上进行抗紫外线处理的可行性。     

An Investigation of Vibration Reducing on a Machine Tool

In order to reduce the vibration on a machine tool, more orthogonal experiment schemes have been designed, which are based on the steel balls vibration reducing principle. After experiments the optimal reducing vibration scheme was determined. This kind of vibration reducing scheme is used in steel balls vibration absorber, which can be used to reduce vibration magnitudes of a machine tools under the working conditions, whereby improving machining precision. The suggested experiment method is of useful reference in reducing vibrations on other machine tools too.