Annual and regional variations of aflatoxin B1 levels seen in grains and feed coming from Croatian dairy farms over a 5-year period

The aim of the study was to investigate annual and regional differences in the level of aflatoxin B₁ (AFB₁) in grains and dairy cattle feed. Maize (n = 972), wheat (n = 201), barley (n = 147), oat (n = 136), grain mixtures (n = 168), and dairy cattle feed (n = 325) were sampled from 2009 to 2013 on different farms and in different farm factories situated in four Croatian regions. The samples were analysed for AFB₁ using the validated ELISA immunoassay. AFB₁ was determined in 16.4% of all investigated samples, among which maize was proven to be the most contaminated, with 21.7% of the samples recovered during 2013 harbouring AFB₁ in concentrations over the permissible ones. Levels higher than permitted were observed in 17.9% and 12.3% of grain mixtures and dairy cattle feed, respectively, whereas concentrations of AFB₁ determined in other crops throughout the investigated period met the stipulated requirements. The results revealed the AFB₁ occurrence to be significantly (p < 0.05) dependent on the cultivation region, with the highest levels generally found in maize harvested in 2013 and consequently in grain mixtures and cattle feed that can most likely be associated with climatic conditions as the most critical factor for mould formation, and thus also AFB₁ production.     

仙游抽水蓄能电站尾水系统充排水试验

为检查工程质量,查找输水系统可能存在的问题并消除隐患,保障电站安全运行,福建仙游抽水蓄能电站在投产发电前,要对输水发电系统进行充水试验与放空排水试验,在试验过程中监测输水系统的应力、应变与渗漏水情况。本文以尾水系统为例,介绍了试验所应具备的工程条件、工作程序及技术要求、试验成果分析和存在问题处理等。试验表明,仙游抽水蓄能电站尾水系统设计合理,施工质量优良,结构可靠,可供同类工程参考与借鉴。     

Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

乙烯、丙烯中微量水含量的分析

采用便携式微量水分析仪和库仑法微量水分析仪测定了乙烯、丙烯试样中的微量水含量,对试样的传输系统、进样量的控制、液体试样的气化和水标准气体的制备方法进行了改进,优化了测试条件。以低吸附惰性管线和小死体积单进单出的不锈钢减压器为试样传输系统,缩短了测试时间。采用液态烃闪蒸气化取样进样器气化液体试样并准确控制试样的进样量,可避免液体试样渐次气化对水含量测定结果的影响及对采样钢瓶大小的限制。采用渗透管发生器制备水标准气体,可验证分析结果的准确度。采用库仑法微量水分析仪测定水含量时,试样流量选择600 m L/min较适宜,开封保存15 d之内的卡尔·费休试剂对测定结果无影响。采用便携式微量水分析仪测定水含量时,选择试样流量在400~800 m L/min之间较适宜。两种仪器的测量结果相近,稳定性好,准确度高,回收率在102%~107%之间,相对偏差小于10%。     

黑龙江省节水增粮行动(2012—2015年)实施方案

文章通过对黑龙江省高效节水现状,存在问题的分析,结合黑龙江省高效节水发展的支撑能力,阐述黑龙江省节水增粮目标、任务及总体布局,为黑龙江省2012—2015年节水增粮实施提供依据。     

Combination of heat treatment and chitosan coating to improve postharvest quality of wolfberry (Lycium barbarum)

The synergistic application of hot water dip at 42 °C for 30 min and 1% chitosan coating on differentiation in postharvest quality traits, microstructure as well as microbiological evolution of wolfberry fruits was investigated. Fresh wolfberry fruits were stored at 2 ± 0.5 °C and 90% relative humidity (RH) for 28 days. Results indicated the combination of prestorage heat treatment and chitosan coating maintained higher levels of ascorbic acid, total phenolic contents and antioxidant capacity as well as lower decay, compared with untreated wolfberry fruits. The possible mechanism was that the heat treatment almost sealed open stomata to limit the sites of pathogen penetration into fruits independently, followed by the biofilm formed by chitosan which controlled secondary infections as well as slowed changes in fruit respiration and metabolic activity in wolfberries. The synergistically treated fruit also exhibited a higher acceptability obtained by sensory analysis after cold storage. In this sense, the integrated application of heat treatment and chitosan coating could be regarded as an effective strategy to extend storage life and maintain the postharvest quality of wolfberry fruits.     

浅谈氯碱氢的一种深度脱水工艺

概述了氢的主要工业生产方法和实际应用,详细介绍了氯碱氢三级脱水工艺过程,并运用在线分析手段,准确显示了干燥过程中的氯碱氢水分含量变化规律。     

Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.