Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

应用改进BP网络对潼关高程的预测

作者在分析了影响汛前和汛后潼关高程变化值的因素的基础上，利用改进BP网络模型对非特征汛期和汛期潼关高程的变化值进行了计算。计算中不采用潼关的绝对高程，而用高程的变化量作为网络的较出物正量，从而减少计算误差，同时又能客观地考虑各影响因子的作用。改进后的BP模型学习时间短，精度满足要求。用该模型计算的潼关高程变化趋势与实际水库调度运行中的高程基本吻合。     

珠江三角洲网河近20年河床演变特征分析

总结了20世纪80年代前珠江三角洲网河河床演变特征,并采用80年代和90年代末的河道地形图,通过对比珠江三角洲各主要河道的深泓线、平均河底高程以及河道容积、河床断面宽深比的变化,分析珠江三角洲80年代后的河床演变特征。对比分析结果表明珠江三角洲在不同时期呈现出不同的河床演变规律——20世纪80年代前以淤积为主,80年代至90年代末转变为以冲刷为主。     

Characterization and optimization of copper chemical mechanical planarization

The feature scale planarization of the copper chemical mechanical planarization (CMP) process has been characterized for two copper processes using Hitachi 430-TU/Hitachi T605 and Cabot 5001/Arch Cu10K consumables. The first process is an example of an abrasive-free polish with a high-selectivity barrier slurry, while the second is an example of a conventional abrasive slurry with a low-selectivity barrier slurry. Copper fill planarization has been characterized for structures with conformal deposition as well as with bumps resulting from bottom-up fill. Dishing and erosion were characterized for several structures after clearing. The abrasive-free polish resulted in low sensitivity to overpolish and low saturation levels for dishing and erosion. Consequently, this demonstrated superior performance when compared to the International Technology Roadmap for Semiconductors (ITRS) 2000 roadmap targets for planarization. While the conventional slurry could achieve the 0.13-μm technology node requirements, the abrasive-free polish met the planarization requirements beyond the 0.10-μm technology node.     

利用黄河泥沙加固下游大堤

黄河是一条举世闻名的多泥沙河流，善淤、善决、善徒给沿河人民带来对过深重灾难，防洪问题一直是国家的心腹之患。泥沙问题是黄河防洪问题的症结所在。在总结固大堤经验的基础，进行挖河疏浚，淤筑“相对地下河”，已作为黄河治理的一项重大决策付诸实施。     

云南滇池湖泊流域水土流失灾害遥感调查

采用遥感技术与地面调查相结合的方法，组织多学科综合调查研究，对云南滇池流域水土流失状况及程度进行了调查分析。初步查明了引起水土流失灾害的原因并提出相应的防止对策。     

换热站容积式加热器管束失效原因及防护

对换热站容积式加热器管束失效原因进行了分析 ,指出主要是由于汽蚀和电化学腐蚀所致。从操作工艺和采用 12Cr2AlMoV材质两方面进行改进 ,可使管束的使用寿命由 4个月延长到 2年