Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

Effect of wind condition on unintended hydrogen release in a hydrogen refueling station

Ambient condition, especially the wind condition, is an important factor to determine the behavior of hydrogen diffusion during hydrogen release. However, only few studies aim at the quantitative study of the hydrogen diffusion in a wind-exist condition. And very little researches aiming at the variable wind condition have been done. In this paper, the hydrogen diffusion in different wind condition which including the constant wind velocity and the variable wind velocity is investigated numerically. When considering the variable wind velocity, the UDF (user defined function) is compiled. Characteristics of the FGC (flammable gas cloud) and the HMF (hydrogen mass fraction) are analyzed in different wind condition and comparisons are made with the no-wind condition. Results indicate that the constant wind velocity and the variable wind velocity have totally different effect for the determination of hydrogen diffusion. Comparisons between the constant wind velocity and the variable wind velocity indicate that the variable wind velocity may cause a more dangerous situation since there has a larger FGC volume. More importantly, the wind condition has a non-negligible effect when considering the HMF along the radial direction. As the wind velocity increases, the distribution of the HMF along the radial direction is not Gaussian anymore when the distance between the release hole and the observation line exceeds to a critical value. This work can be a supplement of the research on the hydrogen release and diffusion and a valuable reference for the researchers.     

2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

Numerical study on laminar burning velocity of ammonia flame with methanol addition

The combustion characteristics of ammonia/methanol mixtures were investigated numerically in this study. Methanol has a dramatic promotive effect on the laminar burning velocity (LBV) of ammonia. Three mechanisms from literature and another four self-developed mechanisms constructed in this study were evaluated using the measured laminar burning velocities of ammonia/methanol mixtures from Wang et al. (Combust.Flame. 2021). Generally, none of the selected mechanisms can precisely predict the measured laminar burning velocities at all conditions. Aiming to develop a simplified and reliable mechanism for ammonia/methanol mixtures, the constructed mechanism utilized NUI Galway mechanism (Combust.Flame. 2016) as methanol sub-mechanism and the Otomo mechanism (Int. J. Hydrogen. Energy. 2018) as ammonia sub-mechanism was optimized and reduced. The reduced mechanism entitled ‘DNO-NH3’, can accurately reproduce the measured laminar burning velocities of ammonia/methanol mixtures under all conditions. A reaction path analysis of the ammonia/methanol mixtures based on the DNO-NH3 mechanism shows that methanol is not directly involved in ammonia oxidation, instead, the produced methyl radicals from methanol oxidization contribute to the dehydrogenation of ammonia. Besides, NO_x emission analysis demonstrates that 60% methanol addition results in the highest NO_x emissions. The most important reactions dominating the NO_x consumption and production are identified in this study.     

Ultrasonic tomographic velocimeter for visualization of axial flow fields in pipes

An ultrasonic tomographic velocimeter to provide quantitative images of axial flow fields in pipes is developed and presented in this work. To detect the flow in various directions and positions, a novel transducer configuration strategy is proposed. All-in-one transducers are mounted in two sectional planes of the pipe. In each plane, N transducers are equally spaced along the circumference. Overlapped propagation paths are introduced by the configuration strategy, and the influence of the vortex flow can be eliminated theoretically by averaging the line velocities of the overlapped paths. To achieve a fast detection speed, the projection data is collected via an electrical scan in a fan-beam mode. After rearrangement and interpolation of the projection data, the parallel beam filtered back projection (FBP) algorithm is implemented to reconstruct the axial flow field. Numerical simulations with the theoretical velocity profiles were performed. The compensation method for the vortex flow is proved to be effective and necessary, and the number of transducers required for reconstruction of common flow profiles was estimated. Accordingly, an ultrasonic tomographic velocimeter consisting of 2×12 transducers was fabricated. Experiments were conducted in the straight pipe and downstream of a single bend pipe and compared with the computational fluid dynamics (CFD) simulation results. As demonstrated, the ultrasonic tomographic velocimeter was capable of visualizing both symmetric and asymmetric axial flow fields with high reliability.     

基于梯度提升决策树的车轮轮缘厚度磨耗预测

轮对在列车走行过程中起着导向、承受以及传递载荷的作用，其踏面及轮缘磨耗对地铁列车运行安全性和钢轨的寿命都将产生重要影响。根据地铁列车车轮磨耗机理，分析车轮尺寸数据特点，针对轮缘厚度这一型面参数，基于梯度提升决策树算法构建轮缘厚度磨耗预测模型。在该模型的基础上，任意选取某轮对数据进行验证分析，结果表明：基于梯度提升决策树的轮对磨耗预测模型具有较好的预测精度，可预测出1~6个月的轮缘厚度变化趋势范围，预测时间范围较长，可为地铁维保部门对轮对的维修方式由状态修转为预防修提供指导性建议。     

In situ efficiency of filters in residential central HVAC systems

High-efficiency filtration in residential forced-air heating, ventilation, and air conditioning (HVAC) systems protects equipment and can reduce exposure to particulate matter. Laboratory tests provide a measure of the nominal efficiency, but they may not accurately reflect the in situ efficiency of the filters because of variations in system conditions and changes in filter performance over time. The primary focus of this paper is to evaluate the effective filtration efficiency, which is inclusive of any loading and system impacts, in 21 occupied residential homes through in-duct concentration measurements. We considered the role of filter media by testing both electret and non-electret media, as well as the role of loading by considering new and used filters. The results show that filters with higher nominal efficiency generally had higher effective filtration efficiency in the same home. In terms of performance change, there is no significant difference in efficiency between initial and 3-month non-electret filters, but the efficiency of electret filters generally decreased over time. However, both nominal efficiency and performance change were vastly overshadowed by the wide variety in loading and system conditions across homes, making it hard to predict filter efficiency in a given home without in situ measurements.     

Evolving an Accurate Decision Tree-Based Model for Predicting Carbon Dioxide Solubility in Polymers

Solubility is one of the most indispensable physicochemical properties determining the compatibility of components of a blending system. Research has been focused on the solubility of carbon dioxide in polymers as a significant application of green chemistry. To replace costly and time-consuming experiments, a novel solubility prediction model based on a decision tree, called the stochastic gradient boosting algorithm, was proposed to predict CO₂ solubility in 13 different polymers, based on 515 published experimental data lines. The results indicate that the proposed ensemble model is an effective method for predicting the CO₂ solubility in various polymers, with highly satisfactory performance and high efficiency. It produces more accurate outputs than other methods such as machine learning schemes and an equation of state approach.     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.