Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

啤酒标签用铝箔力学性能研究

分析研究了连续铸轧坯料的合金成分，冶金组织和热处理工艺对啤酒标用铝箔力学性能的影响，选定成形性优良的合金系列，并优化铸轧工艺和热处理工艺是提高铝箔力学性能的关键。     

HDPE/CB-GP复合材料体系电性质的研究

当HDPE含量46％（质量分数，以下同）、其它添加剂（如抗氧剂、阻燃剂、交联剂和润滑剂等辅助填料）的含量11％，两种导电填料石墨（GP）和碳黑（CB）的总含量为43％时，研究结果表明石墨含量的变化对HDPE/CB-GP复合材料室温电阻率、阴C强度和后NTC强度有显著的影响．HDPE/CB-GP复合材料中GP的含量〈8．6％时，样品的室温电阻率〈30Ω·m，PTC强度〉7、后NTC强度〈1．3；电阻率．温度曲线经过17次冷热循环后重现性好，复合材料具有实际应用价值；GP在复合材料中为层片状结构。     

10t双电葫芦吊车的改造

介绍了 10t双电葫芦吊车在使用过程中出现的问题 ,提出改造方案     

Thermoplastic elastomeric composition based on maleic anhydride–grafted ground rubber tire

Ground rubber tire (GRT) powder was maleated in an internal mixer using maleic anhydride and dicumyl peroxide at 160°C. Maleated GRT was characterized by using X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, wettability, and differential scanning calorimetry. The physical properties of the dynamically vulcanized 60 : 40, rubber : plastic composition based on acrylated high‐density polyethylene as the plastic phase and ethylene propylene diene rubber containing maleated GRT as the rubber phase were found to be greater than the corresponding composition containing nonmaleated GRT. The blend was found to be reprocessable, like themoplastic elastomers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 370–378, 2002; DOI 10.1002/app.10348     

高密度聚乙烯6300M和2480的耐环境应力开裂性能研究

研究了成型塑料管材的两种牌号的高密度聚乙烯(HDPE)6300M和2480的耐环境应力开裂(ESCR)性能。研究中采用的测试方法为一般弯曲试片法、在管上取样的弯曲试片法和恒定压应变法-压缩环法。根据两种材料测试结果及与其他牌号HDPE测试数据比较,对他们的ESCR进行评价,并讨论和解释了HDPE结构参数,ESCR与韧性形变和脆性断裂之间的联系。     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

瓶级聚酯切片中乙醛含量的控制

对瓶级聚对苯二甲酸乙二酯(PET)原料中的乙醛含量、第三组份(间苯二甲酸)含量、原料比表面积以及工艺参数控制等对产品中乙醛含量的影响进行了讨论，得出了合适的工艺操作条件，并注意到预结晶单元和冷却单元的工艺参数控制对产品乙醛含量的影响最显著，从而为生产乙醛含量小于1．0μg/g的瓶级高粘度PET切片提供了参考。     

高温超高压处理HDPE的WAXD及FT－IR研究

用ＷＡＸＤ和ＦＴ－ＩＲ对高温超高压处理前后的ＨＤＰＥ进行了研究。发现经５．０ＧＰａ的高压处理或２００℃下４．０ＧＰａ的高压同时处理后的ＨＤＰＥ分子链的化学结构未发生变化。ＨＤＰＥ晶体中（２００）面与（１１０）面衍射峰的峰高比（γ）随着压力的升高而增大，表明ＨＤＰＥ分子链在超高压作用下发生了取向排列，且升高温度更有利于这种取向排列，但当压力增大至５．０ＧＰａ及温度升高至２００℃时，γ反而大幅度下降。     

HDPE装置超负荷低能耗生产方案的设计与实施

本文介绍大庆ＨＤＰＥ装置提高生产能力及产品质量的方法。通过采用釜外络合催化剂新技术和提浆液浓度可将ＨＤＰＥ装置聚合釜单釜的生产能力由４．７５ｔ／ｈ提高到５．０ｔ／ｈ，各项能耗下降，收到了增产降耗的显著效果，并使产品质量，产量，品种，能耗，物耗，环保６项指标全部达到了设计要求。