冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

The Einstein relation in nanostructured materials: simplified theory and suggestion for experimental determination

An attempt is made to study the Einstein relation for the diffusivity–mobility ratio (DMR) in quantum wells (QWs) and quantum well wires (QWWs) of tetragonal compounds on the basis of a newly formulated electron energy spectrum taking into account the combined influences of the anisotropies in effective electron mass, the spin–orbit splitting, and the presence of crystal field splitting, respectively. The results for quantum-confined III–V compounds form a special case of our generalized analysis. The DMR has also been studied for QWs and QWWs of II–VI and IV–VI materials. Taking QWs and QWWs of CdGeAs₂, InAs, CdS and PbSe as examples, it was found that the DMR increases with increasing carrier statistics and decreasing film thickness respectively in various oscillatory manners emphasizing the influence of dimensional quantizations and the energy band constants in different cases. An experimental method of determining the DMR in nanostructures with arbitrary dispersion laws has also been suggested and the present simplified analysis is in agreement with the suggested relationship. The well-known results for nanostructures with parabolic energy bands have also been obtained as special cases from this generalized analysis under certain limiting conditions.     

钼丝断裂行为研究

通过对钼丝生产过程中出现的断口实物样分析，阐明造成钼丝断裂的原因，提出钼丝生产用金属钼棒及其拉拔生产的关键工艺参数控制原理，达到降低钼丝断裂几率，提高综合成材率的目的。     

Shallow hydrogen-induced donor in monocrystalline silicon and quantum wires

Electrical and optical properties of bistable shallow donors in monocrystalline silicon, which are introduced by proton implantation followed by annealing at 450 °C, have been studied. The temperature dependences of equilibrium and non-equilibrium carrier concentration and relaxation kinetics were investigated. IR absorption lines of bistable shallow donor electronic excitations were detected. The obtained experimental data demonstrate that the bistable shallow donors can be identified as quantum wire defect nanoclusters.     

高硬度耐磨电弧喷涂管状丝材的研究

利用自熔性合金与非晶态材料的特点，研制了Fe—B系管状丝材作为电弧喷涂材料，其形成的涂层具有良好的结合强度、低的孔隙率、高的硬度和耐磨损性能。     

尼龙护套电线印字缺陷的分析及改进的措施

阐述了尼龙护套电线印字过程中,经常出现的几种缺陷,并对这些缺陷产生的原因进行了分析,尤其对印字拖印问题,进行了详细和深入的分析,并提出了一系列的改进措施。     

加芯搅拌桩芯桩定位限垂技术的研发与应用

为控制水泥土加芯搅拌桩的芯桩贯入质量,研发了一种基于芯桩定位导向架的定位限垂挑臂装置,并通过采用不同材质、不同尺寸的方法,反复摸索、实施,分析得出了芯桩定位导向架的定位限垂挑臂装置的最优方案。同时,通过运用数据比对、图表说明的方法,有效验证了加芯搅拌桩芯桩定位限垂挑臂装置对于现场施工的重要作用。在新疆地区23450 根加芯搅拌桩工程中进行首次应用,实践表明研发的定位限垂技术可有效控制芯桩贯入的定位和垂直度,提高施工效率。该定位限垂技术经济效益良好,可为今后新疆地区特殊软基处理以及加芯搅拌桩施工提供参考价值。     

人工智能在冷轧带肋钢筋工艺参数优化中的应用

论述了人工智能在冷轧带肋钢筋工艺参数优化中的应用,首先利用神经网络建立起冷轧带肋钢筋工艺参数与产品抗拉强度之间关系的数学模型,然后用遗传算法对工艺参数优化。按优化后的工艺参数在某拉丝加工厂进行了大批量生产试验,产品的合格率达到98%以上,从而为控制冷轧带肋钢筋工艺参数提供了一条行之有效的途径。     

Drawing of square twisted wire

The shape of the deformation zone during drawing of square twisted wires is described in this paper. The condition of the stable deformation of the wire is formulated. This condition is satisfied by the constant value of the pitch of the helical surface of the die. The work focuses on the investigation of the influence of the die cone angle on the drawing parameters, in particular on the drawing stress.     

TANDEM双丝焊在造船拼板焊接中的应用

介绍了TANDEM双丝焊在造船拼板焊接中的原理、应用、工艺结果表明,TANDEM焊接工艺对组对时预留间隙、母材种类的适应性较强,热输入低,变形小,减少焊后处理成本,焊接效率高、焊接速度快.TANDEM焊接工艺是船厂拼板焊接比较理想的焊接工艺.