Experimental study of crystal anisotropy based on ultra-precision cylindrical turning of single-crystal calcium fluoride

To realize ultimately efficient signal processing, it is necessary to replace electrical signal processing circuits with optical ones. The optical micro-resonator, which localizes light at a certain spot, is an essential component in optical signal processing. Single-crystal calcium fluoride (CaF₂) is the most suitable material for a highly efficient optical micro-resonator. The CaF₂ resonator can only be manufactured by ultra-precision machining processes, because its crystal anisotropy does not allow the application of chemical etching. However, the optical micro-resonator's performance depends definitely on the surface integrity.This study investigated the relationship between surface quality after ultra-precision machining and crystal anisotropy. Firstly, crack initiation was investigated on the (1 0 0), (1 1 0), and (1 1 1) planes using the micro-Vickers hardness test. Secondly, brittle-ductile transition was investigated by orthogonal cutting tests. Finally, cutting performance of cylindrical turning was evaluated, which could be a suitable method for manufacturing the CaF₂ resonator. The most difficult point in cylindrical turning of CaF₂ is that the crystalline plane and cutting direction vary continuously. In order to manufacture the CaF₂ optical micro-resonator more efficiently, analysis was conducted on crack initiation and surface quality of all crystallographic orientations from the perspective of slip system and cleavage.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

面向流屑角突变建模的切削状态参数经验公式的获得及应用

从提高流屑角突变模型的预测精度出发,建立了切削状态参数与3个切削控制参数之间关系的新经验公式。提出了一种通过迭代法准确设定有限元仿真软件刀-屑摩擦因数的方法,并通过直角切削Al6061-T6工件的有限元仿真试验,获得了一组不同切削控制参数组合条件下的切削状态参数数据。根据该数据拟合出剪切角φ、刀-屑摩擦角β、剪切应力τs关于刀具前角γ0、进给量f和切削速度v的经验公式,并通过一组直角切削试验,验证了所得经验公式的有效性。将新建经验公式应用于流屑角突变建模过程后,所得模型关于突变临界切削宽度的平均预测误差减小了27.2%。     

机械-射流破岩耦合特性研究

在现代旋转钻井破碎井底岩石中仍是以机械破岩为主，理论与实践证明，射流辅助破岩是提高钻井破岩效率的重要途径，但它们的耦合特性研究极少。文章基于渗流场与应力场的耦合理论分析，进行了机械与射流破岩耦合特性的实验研究。结果表明：射流压力和水楔作用对岩石渗流场、应力场具有重要作用，耦合作用比非耦合作用的破岩效率有较大幅度的提高。在实验条件下，砂岩的耦合作用提高破岩效率40％左右，灰岩的耦合作用提高破岩效率20％左右。     

数控技术及产业发展

简要介绍了我国数控技术和产业发展的状况及当今世界数控技术的发展趋势,对我国发展自己的数控技术及产业途径提出了一些建议。     

基于MODBUS协议的激光雕刻切割系统HMI人机交互设备

近年来,国内激光雕刻切割控制器技术发展迅速,基于PC的传统控制器已相当成熟.为了显著提高工业生产效率,适应工业生产规模扩张的需要以及工业对系统稳定性要求的提高,目前国内几家专业运动控制器厂家已经实现了激光雕刻切割控制器的完全脱机运行.本文针对脱机控制器的需要设计一款人机交互设备,该设备采用AT89C55WD单片机为主控制器,采用标准的MODBUS协议实现HMI与脱机控制器的可靠通讯.     

刀具工作前角时变系统切削稳定性的研究

理论分析和试验结果表明，刀具工作前角时变系统的振动响应幅值比刀具工作前角固定不变的系统的振动响应幅值明显减小．试验在普通车床上进行，刀具工作前角由微机通过步进电机按规定的时变参数控制。     

线切割加工轧辊孔型模板提高精度的方法

详细论述了利用线切割机加轧辊孔型模板中易出现的几种影响加工精度的因素及消除方法，以达到提高模板精度。     

综采工作面过断层采煤实践

介绍了大同煤矿集团公司挖金湾矿断层构造情况。总结了技术经验，针对具体条件，该矿综采过断层采煤采取了直接割煤、割顶（底）和预掘巷与割底相结合等过断层措施，取得了较好的效果。