针对不同地质目标的叠前时间偏移成像解释评价

随着计算机硬件和地震勘探成像技术的发展，叠前时间偏移正逐步替代常规的NMO加DMO加叠后时间偏移成为地震数据成像处理方法的主流。但对于不同的地质目标，叠前时间偏移的成像效果是否优于常规NMO加DMO加叠后时间偏移的成像效果呢？为此，从地震数据成像处理方法、处理流程和处理参数等方面进行了讨论，并基于某地区三维数据常规处理结果和叠前时间偏移处理结果，针对不同地质目标进行了剖析与评价。认为：叠前时间偏移成像的垂向分辨率较常规处理明显降低，但对于空间波阻抗变化明显的河流和断层，叠前时间偏移成像的空间分辨率要高于常规处理；对于小于1／4波长的叠置薄储层，叠前时间偏移成像的垂向和空间分辨率低于常规处理结果。     

Fast handoff with reducing waste rate approach for wireless resources management in UMTS mobile networks

3G Wideband CDMA systems adopt the Orthogonal Variable Spreading Factor code tree as the channelization codes management for achieving high data rate transmission in personal multimedia communications. It assigns a single channelization code for each accepted connection. Nevertheless, it wastes the system capacity when the required rate is not powers of two of the basic rate. One good solution is to assign multiple codes for each accepted connection but it causes two inevitable drawbacks: long handoff delay and new call setup delay due to high complexity of processing with multiple channelization codes, and high cost of using more number of rake combiners. Especially, long handoff delay may result in more call dropping probability and higher Grade of Service, which will degrade significantly the utilization and revenue of the 3G cellular systems. Therefore, we propose herein an adaptive efficient codes determination algorithm based on the Markov Decision Process analysis approach to reduce the waste rate and reassignments significantly while providing fast handoff. Numerical results demonstrate that the proposed approach yields several advantages, including the lowest GOS, the least waste rate, and the least number of reassignments. Meanwhile, the optimal number of rake combiners is also analyzed in this paper. This research was supported in part by the National Science Council of Taiwan, ROC, under contract NSC-93-2213-E-324-018.     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

快速纳秒响应二代近贴聚焦像增强器的批量生产

叙述了二代近贴聚焦像增强器批量生产所用真空设备性能及特点，同时给出了管子工艺考核结果及管子纳秒时间响应特性。工艺考核结果表明，制管工艺可靠、性能稳定，管子批量生产合格率大于70％。     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

涡轮钻具在高陡构造的应用及展望

介绍了涡轮钻具在秋参1井的应用情况,详细叙述了涡轮钻具在山前高陡构造快速钻进及防斜打直方面的优点,与常规钻井相比,机械钻速明显提高,钻井周期明显缩短,钻井成本明显下降,经济效益显著。     

国产延迟树脂在腈纶溶剂NaSCN除杂装置的应用

叙述了国产的延迟树脂与进口DOWEX-11-A8树脂在腈纶厂NaSCN回收模拟装置上的比较试验,由试验数据可得出;国产的延迟树脂NVI脱除率性能略优于美国DOWEX-11-A8树脂,并可替代DOWEX-11-A8树脂应用于腈纶厂延迟装置中。     

Generation of Technology-Independent Retargetable Analog Blocks

This paper introduces a complete methodology for retargeting of analog cells to different sets of specifications. This methodology is technology-independent, thus allowing the migration, from one technology to another, of the circuit under retargeting. Careful integration of the device sizing and layout generation tasks via the incorporation of layout constraints during the sizing process allows to generate fully functional designs in a few minutes. The methodology is illustrated via the retargeting of a fully-differential Miller-compensated two-stage operational amplifier for a new set of specifications and two different technological processes.An erratum to this article can be found at     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。