析出物对IF钢性能的影响

一种阻性的晶闸管控制制动器被用于阻尼向串联补偿传输供电的热电发电机中的瞬态扭。重点放在开发适用的控制算，并通过多种不同的运行方式验证算法。作为一种制动器最优控制的可能方法，本文研究了离散等级一般化预先控制（ＧＰＣ），讨论了系统上ＧＰＣ执行过程中存在一些问题。用Ｐｒｏｎｇ分析来辩识系统传递函数，此传递函数与控制方案的考虑及强度特性有关。     

Dose and dose rate effects on coherent-to-incoherent transition of precipitates upon irradiation

A typical precipitation hardened alloy, Cu-Co dilute alloy was selected to study the precipitation behavior and irradiation effect on precipitates. It is found that the principal effect of ion irradiation on the coherent precipitates is loss of coherency, and TEM cross-section observations show that the fraction of the incoherent precipitates is dependent on dose but not on dose rate during heavy ion irradiation.     

Effect of oxygen precipitates in solar grade silicon on minority carrier lifetime and efficiency of solar cells

The effect of oxygen precipitates on minority carrier lifetime and performance of solar cell was studied by means of Fourier Transform Infrared Spectroscopy (FTIR), quasi-steady state photoconductance (QSSPCD), optical microscope, spectrumresponse and solar cell efficiency test. The minority carrier lifetime and performance of solar cell reduced depend on oxygen precipitates. A few of oxygen precipitates have formed after single-step annealing; and they do not impact the efficiency dramatically. Pre-annealing at 650 ℃ for 4 h enhances the oxygen precipitation when it is subjected to middle temperature annealing. The solar cells performance decayed sharply. Especially annealing at 950 ℃ for 3 h, the V os and I sc of cells decrease 12% and 25% respectively. Few oxygen precipitates have formed in silicon after high temperature annealing at about 1050 ℃ whether pre-annealing is used or not, and the performance of cells is notbe affected.     

铝合金时效-屈服强度的实验与模型化研究

以析出热力学、长大动力学及位错理论为基础，研究了铝合金在时效过程中盘／片状、棒／针状析出相尺寸、体积分数对时效合金强化效果的影响，从微观-宏观相结合的角度建立了具有盘／片状、棒／针状细小时效强化相铝合金的时效工艺-屈服强度量化模型，并通过513K温度下时效Al-Cu-Mg合金和463K温度下时效Al-Mg-Si合金的实验结果对模型进行了验证，取得了较满意的吻合结果，并对本模型的模拟精度与时效析出相参数之间的关系进行了讨论。     

Influences of dehydrating process on properties of ATO nano-powders

1　INTRODUCTIONCrystallineSbdopedtinoxide (ATO) ,cassiteritestructure ,isawidebandgapn typesemiconductor.Be causeofitsopticalproperty (transparentforvisiblelightandreflectiveforIR )andelectroconductibility ,goodchemicalandmechanicalstability ,ithasmanyapplica tions,suchastransparentconductiveelectrodes ,photo voltaicdevices ,photosensors ,catalyst,antistaticcoatingsandelectrochromicmaterials[14 ] .AvarietyoftechniqueshavebeenusedtoprepareATOsuperfinepowders ,someinvolvedryprocesses ,ot…     

磁性纳米SO4^2-／Fe3O4-ZrO2固体超强酸催化合成己二酸二正辛酯

利用磁性对纳米固体超强酸组合，制备出磁性纳米SO4^2-／Fe3O4-ZrO2固体超强酸催化剂，并用TEM、IR、Hammett指示剂检测磁性纳米固体超强酸催化剂性能。将其用于己二酸二正辛酯（DOA）的合成反应中。得到最佳反应条件为负压下，反应温度155℃，n（正辛醇）：n（己二酸）=3．2：1，反应时间2h，w（催化剂）=1．5％，己二酸的转化率达99％。利用催化剂的磁性可将纳米颗粒催化剂迅速分离，回收率达93．8％，并能重复使用。     

卷取温度对X80管线钢析出行为与性能的影响

观察了不同卷取温度下X80管线钢中析出物的情况,并结合其组织性能对比可知：在实验情况下,480℃卷取时,有大量细小弥散的Nb、V的碳氮化物析出物,起到了较好的析出强化作用.     

一种高铬马氏体耐热钢的显微组织和力学性能

研究了高铬马氏体耐热钢(0.09C-10.2Cr-0.52Ni-1.52Mo-0.22V-0.07Nb-3.0Co-0.01Ti-0.0129N-0.0033B)的显微组织和力学性能.结果表明该钢经1100℃×1h空冷正火处理 750℃×1h空冷回火处理后的显微组织为板条状马氏体,在原奥氏体晶界和板条间分布有M23C6碳化物,并有少量1～3μm的M3B2颗粒,马氏体板条内部有10～30 nm的MX型析出相.短期蠕变试验数据显示其在650℃的蠕变性能优于P92钢.     

Relation between impurities and oxide-scale growth mechanisms on Ni-34Cr and Ni-20Cr alloys. II. Influence of sulphur

The oxidation of presulphidized Ni-Cr alloys has been studied by taking into account the influence of the two distinct oxidation mechanisms described in part I of this article. Sulphur enters the Cr₂O₃ scale (in Ni-34Cr alloys) mainly as S^2– species, which at high temperatures increases the V_Cr content, and hence the oxidation kinetics. Sulphur is randomly distributed in the scale, except at the inner oxide-alloy interface, where intergranular microsulphides are analyzed in the oxide-scale zone. In the case of NiO, NiCr₂O₄, Cr₂O₃ oxide multilayers (in a Ni-20Cr alloy), sulphur in the S^2– state is distributed in the oxide layers or at Si-precipitate interfaces. Such a distribution leads to crack formation, especially during cooling.     

2091Al－Li合金晶界无析出带的形成及其对应力腐蚀的影响

用慢应变速率拉伸试验研究不同冷却介质淬火并时效的２０９１合金的应力腐蚀敏感性．用透射电镜观察合金的微观组织．结果表明，晶界无析出带（ＰＦＺ）随淬火速度的提高而变窄；而时效过程中，随着晶界沉淀相的形核和长大，ＰＦＺ逐渐宽化．这说明，时效初期，ＰＦＺ是由空位贫化机制形成的；而伴随时效过程的进行，ＰＦＺ又以溶质贫化机制产生宽化．ＰＦＺ宽度越大，合金应力腐蚀敏感性越大．