miPP/ziPP共混体系的流动性能

首次对茂金属聚丙烯(miPP)／齐格勒-纳塔聚丙烯(ziPP)共混体系的流动性进行了系统的研究。研究发现，在miPP／ziPP共混体系中，miPP含量的变化改变了共混体系的相结构，这种相结构会随着温度和剪切速率的变化而产生明显的变化，从而改变了体系的流动性能，且该共混体系在不同剪切速率下的流动曲线可以分别通过两个模型进行模拟。     

喷射轧制Fe-4.5%Si硅钢片的组织和性能

采用喷射成形和轧制工艺制备了厚度为0.5mm的Fe-4.5%Si高硅钢片，并对其密度、显微组织和电磁性能进行了测试分析，研究结果表明：在最佳的喷射成形和轧制工艺条件下，所制备硅钢片的磁感应强度B25为1.544T、B50为1.641T；铁损P1050为1.437W/kg、P1550为3.43W/kg，说明喷射成形轧制技术可以制备出高磁感应强度、低铁损的高硅钢片。     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

冷成型模具低温锌系磷化

研制出适用于冷成型模具高硬度表面的低温锌系磷化工艺。其中磷化液含Zn(H2 PO4 ) 2 ·2H2 O 6 0g/L ,Zn(NO3) 2 ·6H2 O 90g/L ,NaNO2 1.5g/L ,稀土促进剂 0～ 1.0g/L ,游离酸度 4～ 6点 ,总酸度 70～ 75点。该磷化液在 4 0℃下 ,处理 30～ 4 0min后可获得厚约 10 μm的磷化膜。性能测试表明 ,其减摩、润滑性能良好 ,摩擦系数约降 0 .1,与未处理试样相比磨损量下降 96 % ,附着力 1级。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案     

枣35断块沙三段玄武岩储层特征及成藏条件分析

从地质、地震、测井及试油试采等方面入手，并采用新技术，对自来屯构造枣35断块沙三段玄武岩储层特征及成藏条件进行了分析。其结果为该区下一步勘探、开发及进一步研究奠定了基础。     

关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

空心微珠改性硬质聚氯乙烯复合材料的应用研究

经过改性的超细空心微珠可以作为填料加入到硬质聚氯乙烯（PVC－U）树脂中，同时改善PVC树脂的流变性、冲击性能和刚性等性能。研究结果表明，超细空心微珠加入到硬质PVC管材中，可以明显改善PVC硬管的加工流动性能，显著缩短塑化时间，降低最大扭矩。而超细空民微珠加入到硬质PVC板材时，可以提高PVC硬板的冲击性能，减小制品的收缩率，赋予PVC硬板优异的耐腐蚀性能，且产品的各项性能均符合PVC板材国家标准GB／T4454－96。