Constructing developable surfaces by wrapping cones and cylinders

We model developable surfaces by wrapping a planar figure around cones and cylinders. Complicated developables can be constructed by successive mappings using cones and cylinders of different sizes and shapes. We also propose an intuitive control mechanism, which allows a user to select an arbitrary point on the planar figure and move it to a new position. Numerical techniques are then used to find a cone or cylinder that produces the required mapping. Several examples demonstrate the effectiveness of our technique.     

Thermal Bending Analysis of Doubly Curved Composite Laminated Shell Panels with General Boundary Conditions and Laminations

Thermal bending analysis of doubly curved laminated shell panels with general boundary conditions and laminations is presented. The equations of equilibrium are derived in the form of two coupled sets of ordinary differential equations based on a general shell theory and solved through the state-space approach in a repeated manner. It is depicted that the results of the present method are in great agreement with analytical solutions. Cylindrical shell panels with general boundary conditions and laminations, where no analytical solution is available, are solved. It is found that the present method exhibits a high convergence rate as well as presenting accurate results in all cases.     

径向水平井弯曲转向机构影响因素仿真研究

针对径向水平井钻进中钻杆弯曲转向前进运动困难的问题,通过建立弯曲转向机构仿真有限元模型,对其主要影响因素:滑道轨迹曲率、间隙、工作压力、滚轮形状与位置和钻杆壁厚等用ANSYS软件进行仿真研究。研究表明:影响截面变形的主要因素是滑道曲率的改变和滑道摩擦因数,钻井失败时钻杆所受阻力的增大不是因为升高工作压力导致截面变形过大与滑道干涉所致,钻杆经校直段,钻头中轴线与校直中心线存在一定的角度,即钻杆的前进轨迹就会偏离理论值,或与地层干涉,或可能再次发生弯曲变形;另一主要原因是转向器滑道工作恶化。增加钻杆壁厚,降低工作压力和滑道摩擦因数,设计合理弯曲转向机构是解决问题的关键。     

两种基于弯曲损耗的光纤测试仪器原理及应用

光纤通信技术的飞速发展带动了光纤测试仪器的发展。主要对两种利用弯曲损耗对光纤进行检测的仪器——光纤识别仪、光纤对线器的原理、结构及其在光纤通信工程中的应用进行了阐述，两种仪器可以在不中断光纤通信的情况下对光纤进行检测，极大地降低了对光纤通信系统的影响，对光纤通信系统具有重要意义。     

黄河黑山峡河段大柳树水库比小观音水库原始库容多40亿m3的作用

一级开发大柳树高坝原始库容比二级开发小观音高坝多 4 0亿m3 ,库容大带来的好处体现在 5～ 7月可多向下游增供水量 ,缓解下游河道断流 ;延长泄放清水时间 ;增加发电效益 ;满足宁蒙河段防凌要求 ;增加汛期集中泄水 ,减缓下游河道淤积萎缩 ;满足南水北调西线工程水量调节要求等。为了更好优化配置黄河水资源 ,从全局和长远利益考虑 ,应采用一级开发方案 ,修建大柳树高坝大库     

弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

A Mixed-Approach Analysis of Deformations in Pipe Bends. Part 3. Calculation of Bend Axis Displacements by the Method of Initial Parameters

A problem of deformation of a curved shell loaded by internal pressure, axial force, and temperature difference is discussed. Physical equations are derived whereby the displacements and angles of rotation of the line of centers of mass of cross sections of a shell are related to loading parameters. A general constitutive set of equations for a curved element during its deformation is given. Using a method of initial parameters, an analytical solution is obtained for the differential equations for displacements and angles of rotation of the center line allowing for the action of distributed forces and moments.     

直缝焊管机组生产冷弯型钢产品初探

主要介绍了φ２１９直缝焊管机组生产高速公路护栏 成型原理、工艺布置、变形方式、变形图和轧辊设计。