Al、Mo含量对铸造钛合金力学性能的影响

运用正交实验 ,考察了Al、Mo含量对Ti Al Mo 1Zr系铸造钛合金力学性能的影响。试验结果表明 :随Al、Mo含量提高 ,铸造合金的强度增加 ,塑性和冲击韧性降低 ,但Al、Mo的交互作用却使合金塑性提高 ,强度和冲击韧性降低     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

钛铜复合棒及其标准化

概述了钛铜复合棒研制开发及发展历程,并介绍了钛铜复合棒的主要性能,以及钛铜复合棒的标准化情况。     

钛的应用及前景展望

从传统应用及新兴应用两方面对钛的应用进行了综述,并对钛的应用前景进行了展望。     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

影响铁精矿K2O、Na2O、SiO2含量的因素分析

用统计分析方法 ,分析了影响精矿K2 O、Na2 O、SiO2 含量的因素 ,并根据分析结论提出了对生产工艺进行定向控制的条件