PID Control of Planar Nonlinear Uncertain Systems in the Presence of Actuator Saturation

This paper investigates PID control design for a class of planar nonlinear uncertain systems in the presence of actuator saturation. Based on the bounds on the growth rates of the nonlinear uncertain function in the system model, the system is placed in a linear differential inclusion. Each vertex system of the linear differential inclusion is a linear system subject to actuator saturation. By placing the saturated PID control into a convex hull formed by the PID controller and an auxiliary linear feedback law, we establish conditions under which an ellipsoid is contractively invariant and hence is an estimate of the domain of attraction of the equilibrium point of the closed-loop system. The equilibrium point corresponds to the desired set point for the system output. Thus, the location of the equilibrium point and the size of the domain of attraction determine, respectively, the set point that the output can achieve and the range of initial conditions from which this set point can be reached. Based on these conditions, the feasible set points can be determined and the design of the PID control law that stabilizes the nonlinear uncertain system at a feasible set point with a large domain of attraction can then be formulated and solved as a constrained optimization problem with constraints in the form of linear matrix inequalities (LMIs). Application of the proposed design to a magnetic suspension system illustrates the design process and the performance of the resulting PID control law.      

Domain reversal and current transport property in BiFeO3 films

The electrical properties and domain reversal in BiFeO₃ ferroelectric films were studied using sandwiched heterostructures and piezoresponse force microscopy. A robust polarization state was observed, combined with a switchable domain pattern and a remanent polarization of approximately 100 μC cm^?2. In addition, domain reversal was explored using scanning probe microscopy. The results show that dipoles could be reversed along the direction of the electric field under a negative tip bias, leading to carrier gathering near the domain walls. The enhanced conductivity near the domain walls was owing to the discontinuous polarization boundary conditions. In addition, typical diode-like current transport properties are sensitive to various temperature conditions, which is attributed to the Schottky barriers at the contact interface. These findings extend the current understanding of domain texture reversal in ferroelectric films and shed light on their potential applications for future ferroelectric random-access memory operations over a wide temperature range.     

Stress wave propagation in adhesively bonded functionally graded cylinders: an improved model

This study presents an improved mathematical model to analyse the stress wave propagation in adhesively bonded functionally graded (FG) circular cylinders (butt joint) under an axial impulsive load. The volume fractions of the material constituents in the upper and lower cylinders were functionally tailored through the thickness of each cylinder using a power-law. The effective material properties of both cylinders, which are made of aluminum (Al) and silicon carbide (SiC), at any point were predicted by using the Mori–Tanaka homogenization scheme. In this improved model, the governing equations of the wave propagation include the spatial derivatives of local mechanical properties and were discretized by means of the finite difference method. The influence of these spatial derivatives and the compositional gradient exponent on the displacement and stress distributions of the joint was investigated. The material composition variations of both cylinders affected the displacement and stress fields whereas the compositional gradient exponent had a minor effect. The stress concentrations were alleviated in time, the displacement and stress distributions/variations around/along the upper and lower cylinder-adhesive interfaces were significantly affected by the adhesive layer. The spatial derivatives also affected the temporal histories of the displacement and stress components evaluated at the selected critical points of the upper cylinder, adhesive layer and lower cylinder. The consideration of the spatial local material derivatives provided a more accurate mathematical model of wave propagations through the graded layered structures.     

基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

Secure image encryption scheme using 4D-Hyperchaotic systems based reconfigurable pseudo-random number generator and S-Box

This paper introduces the design of a hardware efficient reconfigurable pseudorandom number generator (PRNG) using two different feedback controllers based four-dimensional (4D) hyperchaotic systems i.e. Hyperchaotic-1 and -2 to provide confidentiality for digital images. The parameter's value of these two hyperchaotic systems is set to be a specific value to get the benefits i.e. all the multiplications (except a few multiplications) are performed using hardwired shifting operations rather than the binary multiplications, which doesn't utilize any hardware resource. The ordinary differential equations (ODEs) of these two systems have been exploited to build a generic architecture that fits in a single architecture. The proposed architecture provides an opportunity to switch between two different 4D hyperchaotic systems depending on the required behavior. To ensure the security strength, that can be also used in the encryption process in which encrypt the input data up to two times successively, each time using a different PRNG configuration. The proposed reconfigurable PRNG has been designed using Verilog HDL, synthesized on the Xilinx tool using the Virtex-5 (XC5VLX50T) and Zynq (XC7Z045) FPGA, its analysis has been done using Matlab tool. It has been found that the proposed architecture of PRNG has the best hardware performance and good statistical properties as it passes all fifteen NIST statistical benchmark tests while it can operate at 79.101-MHz or 1898.424-Mbps and utilize only 0.036 %, 0.23 %, and 1.77 % from the Zynq (XC7Z045) FPGA's slice registers, slice LUTs, and DSP blocks respectively. Utilizing these PRNGs, we design two 16 × 16 substitution boxes (S-boxes). The proposed S-boxes fulfill the following criteria: Bijective, Balanced, Non-linearity, Dynamic Distance, Strict Avalanche Criterion (SAC) and BIC non-linearity criterion. To demonstrate these PRNGs and S-boxes, a new three different scheme of image encryption algorithms have been developed: a) Encryption using S-box-1, b) Encryption using S-box-2 and, c) Two times encryption using S-box-1 and S-box-2. To demonstrate that the proposed cryptosystem is highly secure, we perform the security analysis (in terms of the correlation coefficient, key space, NPCR, UACI, information entropy and image encryption quantitatively in terms of (MSE, PSNR and SSIM)).     

5A06-O aluminium–magnesium alloy sheet warm hydroforming and optimization of process parameters

The uniaxial tensile test of the 5A06-O aluminium–magnesium (Al–Mg) alloy sheet was performed in the temperature range of 20–300 °C to obtain the true stress–true strain curves at different temperatures and strain rates. The constitutive model of 5A06-O Al–Mg alloy sheet with the temperature range from 150 to 300°C was established. Based on the test results, a unique finite element simulation platform for warm hydroforming of 5A06-O Al–Mg alloy was set up using the general finite element software MSC.Marc to simulate warm hydroforming of classic specimen, and a coupled thermo-mechanical finite element model for warm hydroforming of cylindrical cup was built up. Combined with the experiment, the influence of the temperature field distribution and loading conditions on the sheet formability was studied. The results show that the non-isothermal temperature distribution conditions can significantly improve the forming performance of the material. As the temperature increases, the impact of the punching speed on the forming becomes particularly obvious; the optimal values of the fluid pressure and blank holder force required for forming are reduced.     

Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Eight-node conforming straight-side quadrilateral element with high-order completeness (QH8-C1)

A new eight-node conforming quadrilateral element with high-order completeness, denoted as QH8-C1, is proposed in this article. First, expressions for the interpolation displacement function satisfying the requirements for high-order completeness in the global coordinate system are constructed. Second, the displacement function expression in global coordinates is transformed into isoparametric coordinates, and the relationships between the two series of coefficients for the two kinds of displacement function expressions are found. Third, the displacement function expression is modified to satisfy the requirements of nodal freedom and interelement boundary continuity. The key to the new element construction is the derivation of the linear relationship expressions among 12 coefficients of element displacement interpolation polynomials in the global and isoparametric coordinate systems. As a result, the relationship between quadratic completeness and interelement continuity is explicitly given, and a proof of the completeness and the continuity was conducted to theoretically guarantee the validity of the derivation results. Furthermore, in order to verify the correctness of the theoretical work, nine numerical examples were performed. The computation results from these examples demonstrate that QH8-C1 exhibited excellent performance, including high simulation accuracy, fast convergence, insensitivity to mesh distortion, and monotonic convergence.     

F-OFDM仿真系统设计与时频同步算法

针对新一代5G波形的F-OFDM技术开展了研究,通过把一个宽带分为若干个子带,对每个子带进行滤波处理以实现更好的通信效能。基于Simulink平台进行了F-OFDM仿真系统的搭建,重点对F-OFDM符号同步方法和频偏估计方法进行了研究与仿真分析。实验结果表明,基于Chu序列相比采用PN序列可以获得更好的同步效果,基于导频的Classen频偏估计算法相比基于CP的CFO估计算法和基于训练序列的Moose估计方法可以获得更好的频偏估计效果。