A Convenient Synthesis of Some Coumarin Derivatives Using SnCl2 · 2H2O as Catalyst

Some substituted coumarins have been synthesized by von-Pechmann condensation using SnCl₂ · 2H₂O (10 mol %) as catalyst in ethanolic medium. The reactions are simple, easy in handling and environmentally benign.     

Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

Recent advances in isotropic conductive adhesives for electronics packaging applications

Isotropic conductive adhesives (ICAs) have recently received a lot of focus and attention from the researchers in electronics industry as a potential substitute to lead-bearing solders. Numerous studies have shown that ICAs possess many advantages over conventional soldering such as environmental friendliness, finer pitch printing, lower temperature processing and more flexible and simpler processing. However, complete replacement of soldering by ICAs is yet not possible owing to several limitations of ICAs which are mainly related to reliability aspects like limited impact resistance, unstable contact resistance, low adhesion and conductivity etc. Continued efforts for last 15 years have resulted in development of ICAs with improved properties. This review article is aimed at providing a better understanding of ICAs, their principles, performance and significant research and development work addressing the technological utility of ICAs.     

Effect of process parameters on impact strength of Al-7% Si alloy castings produced by VAEPC process

The castings produced by the evaporative pattern casting (EPC) process have blow holes. The blow holes in EPC castings are because of the non-escape of the gas produced as a result of burning of polystyrene pattern in the sand mold. To overcome the problem of blow holes, the EPC process is combined with the vacuum (V)- process. The vacuum applied to EPC mold draws the decomposed gases and improves the casting quality produced by the EPC process. The developed hybrid process has been termed as the vacuum assisted evaporative pattern casting (VAEPC) process. The objective of this paper to investigates the effect of process parameters, i.e, degree of vacuum, pouring temperature, grainfineness number, amplitude of vibration and time of vibration on the impact strength of Al-7% Si alloy castings in VAEPC process. In order to evaluate the effect of selected process parameters, the response surface methodology (RSM) is used to formulate a mathematical model which correlates the independent process parameters with the desired impact strength. The central composite rotatable design has been used to conduct the experiments. The results indicate that the impact strength decreases with increases in the grainfineness number and pouring temperature. Whereas, it has an inverse relationship with amplitude of vibration, time of vibration and degree of vacuum. The best value of impact strength (2.34 N/mm²) has been obtained at 400 mm Hg degree of vacuum imposed, 650°C as pouring temperature, 60 as sand grainfineness number, 460 μm as amplitude of vibration, and 70 s as time of vibration.     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.     

Finite sample properties of estimators of spatial autoregressive models with autoregressive disturbances

The article investigates the finite sample properties of estimators for spatial autoregressive models where the disturbance terms may follow a spatial autoregressive process. In particular we investigate the finite sample behavior of the feasible generalized spatial two-stage least squares (FGS2SLS) estimator introduced by Kelejian and Prucha (1998), the maximum likelihood (ML) estimator, as well as that of several other estimators. We find that the FGS2SLS estimator is virtually as efficient as the ML estimator. This is important because the ML estimator is computationally burdensome, and may even be forbidding in large samples, while the FGS2SLS estimator remains computationally feasible in large samples. Received: 20 January 2001 / Accepted: 31 August 2001     

Cooperative cache-based data access in ad hoc networks

Cooperative caching, in which multiple nodes share and coordinate cached data, is widely used to improve Web performance in wired networks. However, resource constraints and node mobility have limited the application of these techniques in ad hoc networks. We propose caching techniques that use the underlying routing protocols to overcome these constraints and further improve performance.