Interfacial Crystallization of Diacylglycerols Rich in Medium‐ and Long‐Chain Fatty Acids in Water‐in‐Oil Emulsions

The effects of diacylglycerols rich in medium‐ and long‐chain fatty acids (MLCD) on the crystallization of hydrogenated palm oil (HPO) and formation of 10% water‐in‐oil (W/O) emulsion are studied, and compared with the common surfactants monostearoylglycerol (MSG) and polyglycerol polyricinoleate (PGPR). Polarized light microscopy reveals that emulsions made with MLCD form crystals around dispersed water droplets and promotes HPO crystallization at the oil‐water interface. Similar behavior is also observed in MSG‐stabilized emulsions, but is absent from emulsions made with PGPR. The large deformation yield value of the test W/O emulsion is increased four‐fold versus those stabilized via PGPR due to interfacial crystallization of HPO. However, there are no large differences in droplet size, solid fat content (SFC), thermal behavior or polymorphism to account for these substantial changes, implying that the spatial distribution of the HPO crystals within the crystal network is the driving factor responsible for the observed textural differences. MLCD‐covered water droplets act as active fillers and interact with surrounding fat crystals to enhance the rigidity of emulsion. This study provides new insights regarding the use of MLCD in W/O emulsions as template for interfacial crystallization and the possibility of tailoring their large deformation behavior. Practical Applications: MLCD is applied in preparing W/O emulsion. It is found that MLCD forms unique interfacial Pickering crystals around water droplets, which promote the surface‐inactive HPO nucleation at the oil‐water interface. Thus MLCD‐covered water droplets act as active fillers and interact with surrounding fat crystals, which can greatly enhance the rigidity of emulsion. This observation would provide a theoretical reference and practical basis for the application of the MLCD with appreciable nutritional properties in lipid‐rich products such as whipped cream, shortenings margarine, butter and ice cream, so as to substitute hydrogenated oil. MLCD‐stabilized emulsions can also be explored for the development of novel confectionery products, lipsticks, or controlled release matrices.     

溶胀嵌入脂肪酸分子制备高脱硼反渗透膜

采用“溶胀-嵌入-收缩”方法改性聚酰胺反渗透膜，制备了一种高脱硼反渗透膜。通过甲醇溶胀增加了高分子链之间的距离，为疏水性癸酸分子的嵌入提供了场所，然后在压力和浓差极化共同作用下，改性分子选择性嵌入聚酰胺膜的孔内；当甲醇分子离开后，聚酰胺膜收缩将癸酸分子固定在高分子网络中。实验借助溶胀和分子嵌入以及溶胀后的收缩调节聚酰胺膜的孔径大小；利用脂肪酸的疏水性降低聚酰胺膜的极性，从而实现增加空间位阻和减少氢键结合位点数量的目的。实验结果显示，改性膜的脱硼率和截盐率均明显升高，截盐率从90.36%增加到96.46%，脱硼率从未改性膜的47.85%增加到77.32%，渗透液的硼含量达到WTO的使用标准。虽然水和硼的渗透性均下降，但是水和硼的渗透选择性增加，证明该方法有利于提高水硼选择性。     

超细粉在内循环流化床中的流态化特性

在内径120 mm的半圆柱形内循环流化床中,以平均粒径387 nm的Ti O2为原料,考察了单独通入流化气、射流气和同时通入流化气和射流气三种流化方式下超细粉的流化特性以及射流气速对超细粉聚团尺寸的影响。结果表明:同时通入流化气和射流气时,流化气能促进粉体循环,消除环隙死区;高速射流能有效破碎聚团,显著减小聚团尺寸,从而使超细粉在环隙区与导流管之间形成稳定循环,小聚团在环隙区实现平稳流态化。随着射流气速的增大,聚团尺寸减小,粒度分布变窄,在射流气速分别为60,90,120,150 m/s的条件下,聚团平均直径分别为194,158,147,135μm。     

Wear mechanism of a novel AlSiMgAl2O4Al2O3 composite used in the low vessel of an RH secondary refining furnace

A novel AlSiMgAl₂O₄Al₂O₃ composite brick was prepared and evaluated in the low vessel of an RH (the initials of Ruhrstahl and Hereaeus) secondary refining furnace; it was characterized by X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. The results show that after use, the AlSiMgAl₂O₄Al₂O₃ composite has a functional gradient with an erosion zone–reinforced zone–original zone phase distribution, in which the phases in the erosion zone (0–1.8?cm) are a Mg-hercynite spinel solid solution, α-Al₂O₃, and minor amount of Al₃Fe₅O₁₂. Furthermore, the phases in the reinforced zone (1.8–5.0?cm) are γ-AlON, 21RSiAlON, SiC, Mg_0.388Al_2.408O₄, and α-Al₂O₃; i.e., the Al and Si in the composite are completely converted into non-oxide reinforced phases. Finally, the phases in the original zone (>5.0?cm) show no change. The reaction mechanism is as follows. During operation, a Mg-hercynite spinel solid solution is formed in the erosion zone due to a reaction between MgAl₂O₄ and FeO from a refinery operation. Therefore, the slag erosion of the material is improved. The Al and Si metals undergo active oxidation, and 21RSiAlON flakes are subsequently formed from the products of the metastable Al₂O(g), SiO(g), and N₂(g) in the ambient. The γ-AlON is formed by a carbothermal reduction nitridation of the α-Al₂O₃ and residual active carbon from the resin binder. The 21RSiAlON and γ-AlON reinforce the composite brick and improve its high temperature performance accordingly. Its service life is 110% that of the magnesia-chrome bricks used in the same period. The reaction model was also established.     

多排陶粒混凝土复合砌块结构优化设计分析

随着我国建筑节能工作的全面推进和不断深化,促进了新型墙体材料的研究和应用.参考相关规范,选取砌块主规格:长×宽×高=390 mm×240 mm×190 mm,根据空心砌块不同孔排数、交错程度和孔洞率,设计12种内部结构不同的空心砌块.通过有限元软件ABAQUS和加权求和法对混凝土自保温空心砌块进行结构优化设计,将优化后的砌块结构浇制成陶粒混凝土空心砌块,空心砌块孔洞由正交试验优化后的泡沫混凝土填充,定量分析不同配比条件下各种材料对泡沫混凝土热工和力学性能影响程度的大小,得到最优配比:水灰比41％,粉煤灰20％,碳酸锂0.16％,聚羧酸减水剂0.075％,微硅粉含量4％和硬质酸钙0.2％,泡沫混凝土的导热系数和抗压强度分别为0.0602 W/(m·K)和5.2 MPa.结合有限元数值模拟和试验研究,制得优化后的陶粒混凝土复合砌块,平均传热系数▉KC3=0.61 W/(m2·K),平均抗压强度10.11 MPa,强度等级达到MU10,同时满足节能65％的要求.     

交联聚乙烯电缆绝缘老化超低频介损试验及评价规程研究

本文基于通过检测电缆超低频介损值确定电缆老化程度的基本原理,结合某地实测得到的多组数据,通过国际规程IEEE 400.2—2013进行初步判断,分析处于不同状态下的电缆介损值的变化规律及其原因,并得出该规程仅适用于没有局部劣化的电缆.此外,由于我国电缆制造材料、结构和生产工艺与国外产品存在差异,采用国际规程判断电缆老化程度有时会变得不准确.为解决此类问题,本文建立更加全面的判据体系,给出最优判断阈值的确定方法,并对该地区实测得到的数据进行拟合,得到更加准确的分级判断阈值.此方法可为建立符合我国电缆实际情况的评价规程提供参考.     

A Dual Inhibitor of DYRK1A and GSK3β for β-Cell Proliferation: Aminopyrazine Derivative GNF4877

Loss of β-cell mass and function can lead to insufficient insulin levels and ultimately to hyperglycemia and diabetes mellitus. The mainstream treatment approach involves regulation of insulin levels; however, approaches intended to increase β-cell mass are less developed. Promoting β-cell proliferation with low-molecular-weight inhibitors of dual-specificity tyrosine-regulated kinase 1A (DYRK1A) offers the potential to treat diabetes with oral therapies by restoring β-cell mass, insulin content and glycemic control. GNF4877, a potent dual inhibitor of DYRK1A and glycogen synthase kinase 3β (GSK3β) was previously reported to induce primary human β-cell proliferation in vitro and in vivo. Herein, we describe the lead optimization that lead to the identification of GNF4877 from an aminopyrazine hit identified in a phenotypic high-throughput screening campaign measuring β-cell proliferation.     

NH2-MCM-41的改性及其pH响应性释药的研究

采用正硅酸乙酯（TEOS）和3-氨丙基三乙氧基硅烷（APTES）通过共缩聚法合成介孔二氧化硅（MCM-41）。首先对其氨基修饰，再通过有机合成接枝—R基团（—R：—CHO、—OH、—CH₃、—COOH），制备得到Me-Ph-NH-MCM-41、OHC-Ph-NH-MCM-41、HO-Ph-NH-MCM-41、HOOC-Ph-NH-MCM-41四种不同的药物载体。利用FT-IR、Zeta电位、XRD和SEM对其结构和形貌表征，结果表明NH₂-MCM-41改性成功。以罗丹明B（RhB）为模型进行载药性能测试，并考察了此释药系统在模拟不同pH的体液下的敏感释药行为，同时探究了不同—R基团对释药的影响。结果显示，四种载体在中性条件下几乎不发生药物释放，通过改变环境体系pH可以有效控制药物释放，其释药行为可以用Korsmeyer-Peppas动力学模型来描述。实验表明，释药量：RhB@HOOC-Ph-NH-MCM-41>RhB@OHC-Ph-NH-MCM-41>RhB@HO-Ph-NH-MCM-41>RhB@Me-Ph-NH-MCM-41，不同—R基团的药物载体的pH响应性不同，其中RhB@HOOC-Ph-NH-MCM-41释药量在pH=1.2时可达57.87%，在用于药物智能控释材料方面具有一定的应用潜力。     

信永中和"登云股份IPO审计失败"探究

本文以证监会发布的针对信永中和及两名签字注册会计师的行政处罚决定书为切入点,结合深圳证券交易所、天眼查、巨潮资讯等网站公布的相关信息,从信永中和的具体审计过程,分析登云股份IPO审计失败的原因,原因主要在于基于业务需要未充分了解公司及其经营环境,贸然接受委托,缺乏应有的执业审慎,缺少了必要的审计程序,复核制度流于形式丧失了发现错误的最后机会。     

电磁精细探测法在隐伏型导水地质裂缝勘探中的应用

针对传统隐伏型导水地质裂缝勘探方法存在勘测精度较差的问题,提出电磁精细探测法探析隐伏型导水地质裂缝。依照屏蔽系数、实测场强和理论场强数据绘制综合曲线图,通过该图获取隐伏型导水地质裂缝所处位置几何阴影范围,采用层析成像法得到网格化的工作面,获取隐伏型导水地质图像。通过图像直接观测隐伏型导水地质工作面裂缝所处位置,在此基础上,观测四个电磁场分量,采用正交电磁场分量计算介质视电阻率,依据计算视电阻率数值和视电阻率分布状态研究裂缝发育情况和裂缝富水程度。结果表明:采用该方法能较为精准地获取隐伏型导水地质裂缝位置。通过裂缝位置进一步检测出隐伏型导水地质裂缝最大发育高度为63.5 m。当视电阻数值不断增加时,隐伏型导水地质裂缝和裂缝富水性逐渐减小,与实际情况较为相符,说明该种方法探析效果较好。