用增量的累积量方法测量大气风场

为了在非平稳、非线性条件下能得到真实风场的良好估计,提出了一种用空间分布天线（SA）雷达信号的增量累积量测量大气风场参数的方法。该方法基于结构函数方法,利用高阶累计量在信息处理中的特性,用零延迟的增量累计量求解平均水平风速等具体参量，并在大气散射模型基础上对增量累积量方法进行了数值模拟,得出了同理论分析一致的结果.分析和计算表明,该方法完全适用于局地平稳条件，可以减小风场参量估计对天线间距的敏感度；阶数k≥3时,对高斯噪声有很强抑制;同时可以得到风场参量的高阶估计，这是普通的二阶方法（如全相关分析、全谱分析）不具备的。     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

降低丙烯酰胺晶体中水份的探讨

本文介绍了如何通过控制结晶时间和离心速率获得低水分的丙烯酰胺晶体，给出了最佳生产工艺条件。     

联产供冷与电力供冷能耗比较分析

文中将两种供冷能耗比较分解成用电煤耗差、用热煤耗量、增加产汽用电煤耗量三部分进行分析，按照热量法得出在目前一般情况下联产供冷比电力供冷通常费能和定性定量结论，为全面研究比较热电冷联产与分产的能耗奠定一个基础。     

间苯二酚的生产技术现状

介绍了间苯二酚的主要用途和国内外生产现状 ,并对主要的生产方法磺化法和氧化法从环境效应上进行了比较 ,对今后我国间苯二酚的生产发展提出了建议     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Spectrum efficient region-based resource allocation with fractional loading for FH-OFDMA cellular systems

A practical resource management method that can significantly reduce cochannel interference (CCI) and improve spectrum utilisation in FH-OFDMA packet-based cellular networks is presented. The proposed method seeks an effective combination of dynamic resource allocation with fractional coding and bit loading to respectively minimise CCI and maximise system throughput for a desired performance.