Droplet-based biochemical assay by magnetic wire manipulation between multiple droplets

Reaction performance of a droplet-based biochemical assay technique that uses magnetic wires as sample carriers is evaluated. Wires 2.0 mm in length, 0.05 mm in width, and 0.02 mm in thickness are fabricated by chemical etching, introduced into a droplet immersed in oil, and manipulated by the magnetic force of a moving magnet. Alkaline-phosphatase as an enzyme is immobilized on the wire surfaces by applying Au and self-assembled monolayer coatings, and the method’s on-chip reaction performance is evaluated. The enzymatic reaction is found to increase linearly as the number of wires and the reaction time increase. Relatively high performance reproducibility for enzymatic reactions is obtained; on average, the reaction absorbance, standard deviation, and coefficient of variance are found to be respectively 1.14, 0.103, and 9.1 %. The conductivity change in a fused droplet is used to evaluate the absolute volume of liquid transferred with the extracted wires and a value of 0.33 μl is obtained.     

Behavior of a mechanically anchored waterproofing membrane system under wind suction and uniform Pressure

A pressure and wind tunnel test was conducted to obtain the basic data for wind resistance design of a mechanically anchored waterproofing membrane system. The test specimen was a flat roof with the following dimensions: 2.4 m in width, 3 m in length and 0.29 m in height. The waterproofing material was polyvinyl chloride sheet reinforced with polyester fiber (PVC sheets). In the pressure test, because the applied pressure was equivalent to the pressure on the entire surface area of the roof, the billowing heights of the PVC sheet around the fastener had almost the same maximum values; therefore, the axial force at the fastener was also similar to the pressure induced by a compressor, and no lateral forces were measured. On the other hand, in the wind tunnel test, the strain of the PVC sheet around the fastener at windward side was larger than that of the leeward side. The lateral force was 70% of the axial force at a mean wind speed of 38.6 m/s. Therefore, it was clear that the characteristics of the mechanically anchored waterproofing membrane system in the pressure test and the wind tunnel test were different.     

Theory of electrostatics and electrokinetics of soft particles

We investigate theoretically the electrostatics and electrokinetics of a soft particle, i.e. a hard particle covered with an ion-penetrable surface layer of polyelectrolytes. The electric properties of soft particles in an electrolyte solution, which differ from those of hard particles, are essentially determined by the Donnan potential in the surface layer. In particular, the Donnan potential plays an essential role in the electrostatics and electrokinetics of soft particles. Furthermore, the concept of zeta potential, which is important in the electrokinetics of hard particles, loses its physical meaning in the electrokinetics of soft particles. In this review, we discuss the potential distribution around a soft particle, the electrostatic interaction between two soft particles, and the motion of a soft particle in an electric field.     

玻璃纤维/大麻纤维增强聚丙烯混杂复合材料的力学性能和断裂特征(英文)

目前在土木工程,建筑,汽车等领域里使用的复合材料中,玻璃纤维是用量最大的增强材料。由于保护地球环境的呼声日趋高涨,天然纤维被期待着代替源于石油而且再利用困难的玻璃纤维,成为绿色复合材料的必要材料之一。本文通过注射成型工艺制作了玻璃短纤维,大麻短纤维以及混杂型纤维增强复合材料,并在拉伸实验中应用两种不同频率的声发射技术检测了拉伸断裂特性。实验发现,随着大麻纤维的加入和混杂复合材料绿色度的增加,复合材料的拉伸弹性模量随之线性增大,而拉伸强度基本保持不变。当大麻纤维的含量超过20wt%的时候,拉伸强度开始降低。在不同频率的声发射实验中,混杂型复合材料的声发射事件的产生都比单一纤维增强型复合材料要来的晚,也就是说,纤维的混杂有助于推迟微裂纹的产生。     

Hydrogen and carbon dioxide adsorption with tetra‐n‐butyl ammonium semi‐clathrate hydrates for gas separations

Gas adsorption rates of H₂, CO₂, and H₂‐CO₂ gas mixture (H₂/CO₂ = 3.4) with tetra‐n‐butyl ammonium salt (bromide, chloride, and fluoride) semi‐clathrate hydrate particles were measured at 269 K to assess their properties for gas separation. Equilibrium gas occupancies in the S‐cages of the particles were in order of (high to low) for hexagonal structure‐I, tetragonal structure‐I, and superlattice of cubic structure‐I structures with the maximum fractional occupancy by CO₂ being about 40%. The CO₂ diffusion rate depended on the anion size of the salt, which is attributed to distortion of the S‐cage that is close to the molecular size of CO₂. Simulations of semi‐clathrate hydrate particles with theory showed that H₂/CO₂ selectivities could be as high as 36 (3.0 mol% TBAF) and that selectivities for an ideal membrane (3.3 mol% TBAF) could be >100 (269 K, 0.3–4.5 MPa). Semi‐clathrate hydrates have wide application as separation media for gas mixtures. © 2014 American Institute of Chemical Engineers AIChE J, 61: 992–1003, 2015     

Thermal Stability,Optical Transmittance,and Refractive Index Dispersion of La2O3–Nb2O5–Al2O3 Glasses

La₂O₃–Nb₂O₅–Al₂O₃ high‐refractive‐index glasses were fabricated by containerless processing, and the glass‐forming region was determined. The thermal stability, density, optical transmittance, and the refractive index dispersion of these glasses were investigated. All the glasses were colorless and transparent in the visible to near infrared (NIR) region and had high refractive index with low wavelength dispersion. Some of these glasses were found to have significantly high glass‐forming ability. These results indicate that the ternary glasses are suitable for optical applications in the visible to NIR region. The effects of the substitution of Al₂O₃ for Nb₂O₅ on optical properties were discussed on the basis of the Drude–Voigt equation. It was suggested that the substitution of Al₂O₃ for Nb₂O₅ increased the molecular density and suppressed a decrease in the refractive index, even when both the average oscillator strength and inherent absorption wavelength decreased in La₂O₃–Nb₂O₅–Al₂O₃ glasses. These results are helpful for designing new optical glasses controlled to have a higher refractive index and lower wavelength dispersion.     

A consistent grayscale‐free topology optimization method using the level‐set method and zero‐level boundary tracking mesh

This paper proposes a level‐set based topology optimization method incorporating a boundary tracking mesh generating method and nonlinear programming. Because the boundary tracking mesh is always conformed to the structural boundary, good approximation to the boundary is maintained during optimization; therefore, structural design problems are solved completely without grayscale material. Previously, we introduced the boundary tracking mesh generating method into level‐set based topology optimization and updated the design variables by solving the level‐set equation. In order to adapt our previous method to general structural optimization frameworks, the incorporation of the method with nonlinear programming is investigated in this paper. To successfully incorporate nonlinear programming, the optimization problem is regularized using a double‐well potential. Furthermore, the sensitivities with respect to the design variables are strictly derived to maintain consistency in mathematical programming. We expect the investigation to open up a new class of grayscale‐free topology optimization. The usefulness of the proposed method is demonstrated using several numerical examples targeting two‐dimensional compliant mechanism and metallic waveguide design problems. Copyright © 2014 John Wiley & Sons, Ltd.     

General topology optimization method with continuous and discrete orientation design using isoparametric projection

A general topology optimization method, which is capable of simultaneous design of density and orientation of anisotropic material, is proposed by introducing orientation design variables in addition to the density design variable. In this work, the Cartesian components of the orientation vector are utilized as the orientation design variables. The proposed method supports continuous orientation design, which is out of the scope of discrete material optimization approaches, as well as design using discrete angle sets. The advantage of this approach is that vector element representation is less likely to fail into local optima because it depends less on designs of former steps, especially compared with using the angle as a design variable (Continuous Fiber Angle Optimization) by providing a flexible path from one angle to another with relaxation of orientation design space. An additional advantage is that it is compatible with various projection or filtering methods such as sensitivity filters and density filters because it is free from unphysical bound or discontinuity such as the one at θ = 2π and θ = 0 seen with direct angle representation. One complication of Cartesian component representation is the point‐wise quadratic bound of the design variables; that is, each pair of element values has to reside in a given circular bound. To overcome this issue, we propose an isoparametric projection method, which transforms box bounds into circular bounds by a coordinate transformation with isoparametric shape functions without having the singular point that is seen at the origin with polar coordinate representation. A new topology optimization method is built by taking advantage of the aforementioned features and modern topology optimization techniques. Several numerical examples are provided to demonstrate its capability. Copyright © 2014 John Wiley & Sons, Ltd.