ORBIT: A parallel computing model of Prolog

This paper proposes a parallel processing model of the Prolog language. The model modifies Or-parallelism by introducing the “process bundle” as a candidate for simultaneous execution. The Process bundle is a subset of backtrack points stacked in depth-first execution. The process bundle includes one or more backtrack points, so it provides a longer process life cycle than the Or-parallel process. A process bundle is dispatched when an idle processor requests a job from an executing processor. The executing processor dispatches a message containing the full environment by which the idle processor can execute the process without any communication with other processors.     

Highly accurate SNR measurement using the covariance of two SEM images with the identical view

Quality of an SEM image is strongly influenced by the extent of noise. As a well-known method in the field of SEM, the covariance is applied to measure the signal-to-noise ratio (SNR). This method has potential ability for highly accurate measurement of the SNR, which is hardly known until now. If the precautions discussed in this article are adopted, that method can demonstrate its real ability. These precautions are strongly related to "proper acquisition of two images with the identical view," "alignment of an aperture diaphragm," "reduction of charging phenomena," "elimination of particular noises," and "accurate focusing," As necessary, characteristics in SEM signal and noise are investigated from a few standpoints. When using the maximum performance of this measurement, SNR of many SEM images obtained in a variety of the SEM operating conditions and specimens can be measured accurately.     

Leak-tightness characteristics concerning the containment structures of the HTTR

The containment structures of the HTTR consist of the reactor containment vessel, the service area, and the emergency air purification system, which minimise the release of fission products in postulated accidents, which lead to fission product release from the reactor facilities. The reactor containment vessel is designed to withstand the temperature and pressure transients and to be leak-tight in the case of a rupture of the primary concentric hot-gas duct, etc. The pressure inside the service area is maintained at a negative pressure by the emergency air purification system. The emergency air purification system will also remove airborne radioactivity and will maintain a correct pressure in the service area.The leak-tightness characteristics of the containment structures are described in this paper. The measured leakage rates of the reactor containment vessel were enough less than the specified leakage limit of 0.1%/d confirmed during the commissioning tests and annual inspections. The service area was kept in a way that the design pressure becomes well below its allowable limitation by the emergency air purification system, which filters efficiency of particle removal and iodine removal well over the limited values.The obtained data demonstrate that the reactor containment structures were fabricated to minimise the release of fission products in the postulated accidents with fission product release from the reactor facilities.     

Safety design

JAERI established the safety design philosophy of the HTTR based on that of current reactors such as LWR in Japan, considering inherent safety features of the HTTR. The strategy of defense in depth was implemented so that the safety engineering functions such as control of reactivity, removal of residual heat and confinement of fission products shall be well performed to ensure safety. However, unlike the LWR, the inherent design features of the high-temperature gas-cooled reactor (HTGR) enables the HTTR meet stringent regulatory criteria without much dependence on active safety systems. On the other hand, the safety in an accident typical to the HTGR such as the depressurization accident initiated by a primary pipe rupture shall be ensured. The safety design philosophy of the HTTR considers these unique features appropriately and is expected to be the basis for future Japanese HTGRs.This paper describes the safety design philosophy and safety evaluation procedure of the HTTR especially focusing on unique considerations to the HTTR. Also, experiences obtained from an HTTR safety review and R&D needs for establishing the safety philosophy for the future HTGRs are reported.     

Mg6Si4O10(OH)8修复剂应用于滑动轴承的模拟试验研究

采用模拟轴承试验机,考察在设计的试验条件下金属磨损自修复层在45#钢/巴氏合金摩擦副间的原位生成及其摩擦学性能。润滑剂使用含适量Mg6Si4O10(OH)8修复剂的SD/CC 40汽油机/柴油机通用油。27 h摩擦试验结束后,采用表面形貌仪、扫描电镜和显微硬度计分析摩擦表面。结果表明,在45#钢表面形成了约2μm厚的自修复层,2个摩擦副表面的表面形貌均有明显改善;显微硬度均有一定的提高,金属磨损自修复层表现出优良的抗磨粒磨损和抗粘着磨损的性能。     

Study of melting and crystallization behavior of polyacrylonitrile using ultrafast differential scanning calorimetry

The thermal behavior of polyacrylonitrile (PAN) has been investigated using X-ray diffraction, differential scanning calorimetry (DSC), and ultrafast DSC. In conventional DSC, it is difficult to prevent the concurrent occurrence of the exothermic reactions of PAN with melting. However, in the ultrafast DSC curve, the exothermic peak due to these reactions disappears over the temperature range 0–400 °C at heating rates above 250 °C s⁻¹. Alternatively, the glass transition and the melting of PAN are observed over the temperature range 109–129 °C and 335–362 °C, respectively. Moreover, upon cooling from the molten state at a rate of −7500 °C s⁻¹, PAN crystallization is observed at 204 °C. These findings were observed repeatedly during heating and cooling measurements. From the extrapolation analysis, the zero-entropy-production melting temperature of PAN is found to lie in the temperature range 320–350 °C. Finally, the equilibrium melting temperature of PAN is estimated to be ca. 465 °C.     

Synthesis of High-Molecular-Weight [60]Fullerene Pearl-Necklace Polyamides Derived from Equatorial [60]fullerenobisacetic Acid

Abstract

A series of [60]fullerene pearl-necklace polyamides, consisting of equatorial-[60]fullerenobisacetic acid and various chromophoric aromatic diamines, were synthesized by a phosphorylation route using large amounts of triphenyl phosphite and pyridine as condensing reagents with stepwise addition of the condensing reagents. In the present polymers, [60]fullerene pearls and diamine linkers were attached to one another by cyclopropane connectors. The polyamides had weight-average molecular weights (M_w)of 4.5-5.0×10⁴ g/mol and inherent viscosities (n _inh) of 0.3-0.4 dL/g in N, N-dimethylacetamide (DMAc) at 30 °C. They had glass transition temperatures at 30-125 °C and decomposition temperatures at 300-310 °C. The UV-VIS spectra in DMAc exhibited broad absorption with λ_max at 310-390 nm tailing to longer wavelengths.     

Neuroprotection,Growth Factors and BDNF-TrkB Signalling in Retinal Degeneration

Neurotrophic factors play key roles in the development and survival of neurons. The potent neuroprotective effects of neurotrophic factors, including brain-derived neurotrophic factor (BDNF), ciliary neurotrophic factor (CNTF), glial cell-line derived neurotrophic factor (GDNF) and nerve growth factor (NGF), suggest that they are good therapeutic candidates for neurodegenerative diseases. Glaucoma is a neurodegenerative disease of the eye that causes irreversible blindness. It is characterized by damage to the optic nerve, usually due to high intraocular pressure (IOP), and progressive degeneration of retinal neurons called retinal ganglion cells (RGCs). Current therapy for glaucoma focuses on reduction of IOP, but neuroprotection may also be beneficial. BDNF is a powerful neuroprotective agent especially for RGCs. Exogenous application of BDNF to the retina and increased BDNF expression in retinal neurons using viral vector systems are both effective in protecting RGCs from damage. Furthermore, induction of BDNF expression by agents such as valproic acid has also been beneficial in promoting RGC survival. In this review, we discuss the therapeutic potential of neurotrophic factors in retinal diseases and focus on the differential roles of glial and neuronal TrkB in neuroprotection. We also discuss the role of neurotrophic factors in neuroregeneration.     

Strength of spline joints assembled by forming

In this paper, a new assembling method of spline joints that enables tight fitting in a simple manner by allowing slight plastic deformation at the spline teeth was introduced. Experiments were carried out for the spline joints of medium carbon steel varying the overlap zone between the male and the female spline teeth. Axial joining strength was increased with increase in the overlap length due to the residual compressive stress by forming. The joint by the proposed method also showed higher torsional strength than the conventional joint. Improvement in the torsional strength was explained based on the deformation and hardness distribution around the spline teeth. With respect to the shape of overlap zone, better results were obtained when using the specimen having a uniform overlap length along the axial direction.     

Effects of phosphorus content on generation and growth of cracks in nickel–phosphorus platings owing to thermal cycling

We observed crack generation and structural changes in electroless nickel–phosphorus (Ni–P) plating layers formed on copper-metalized silicon nitride substrates both during thermal cycling from ? 40 to 250 °C and during storage (not cycling) at 250 °C in order to investigate the effect of the phosphorus contents on crack generation and growth in the Ni–P platings. The used platings contained phosphorus at three different contents: 2.1 wt% [Ni–P(low)], 6.5 wt% [Ni–P(med)], and 10.9 wt% [Ni–P(high)]. The generation time and the amount of cracks were strongly dependent on their phosphorus contents. More cracks appeared after thermal cycling than after storage at 250 °C. In Ni–P(low), cracks were generated after 200 thermal cycles, whereas no cracks were observed even after 250 h of storage at 250 °C. In Ni–P(med) and Ni–P(high), both during thermal cycling and storage at 250 °C, cracks formed during or after crystallization of the amorphous layers. These results suggest that the primary factors affecting the generation of cracks in electroless Ni–P platings are crystallization of the Ni–P platings and repeated changes in thermal stress.