Application of pulse discharge sintering (PDS) technique to rapid synthesis of Ti3SiC2 from Ti/Si/C powders

To synthesize Ti₃SiC₂ samples, pulse discharge sintering (PDS) technique was utilized to sinter elemental powders of Ti/Si/C with stoichiometric and off-stoichiometric ratios in a temperature range of 1200–1500 °C. The results showed that high purity Ti₃SiC₂ could not be obtained from the Ti/Si/C powder with molar ratio of 3:1:2, and Ti₃SiC₂ preferred to form at relatively low sintering temperature for a short time. When 5Ti/2Si/3C and 3Ti/1.5Si/2C powders were sintered for 15 min, the TiC content was respectively decreased to 6.4 and 10 wt.% at 1250–1300 °C. The corresponding relative density of the samples sintered from 5Ti/2Si/3C powder was calculated to be as high as 99% at the temperature above 1300 °C. It is suggested that low-temperature rapid synthesis of Ti₃SiC₂ would be possible through the PDS technique, provided that the composition of the starting powders should be adjusted to be off-stoichiometric ratio from 3:1:2.     

Formation of Sm2+ lons in Sol-Gel-Derived Glasses of the System Na2 O-Al2O3-SiO2

Samarium ions (Sm²⁺) incorporated into aluminosilicate glasses by a sol-gel process showed persistent spectral hole burning at room temperature. Gels of the system Na₂O-Al₂O₃SiO₂ synthesized by the hydrolysis of Si(OC₂H₅)₄, Al(OC₄H₉)₃, CH₃ COONa, and SmCl₃·6H₂O were heated in air at 500°C, then reacted with H₂ gas to form Sm²⁺ ions. Whereas Al³⁺ ions effectively dispersed the Sm³⁺ ions in the glass structure, Na⁺ ions were not effective. The Al₂O₃-SiO₂ glasses proved appropriate for reacting the Sm³⁺ ions with H₂ gas and exhibited the intense photoluminescence of Sm²⁺ ions. The reaction of Sm³⁺ ions with H₂ in the Al₂O₂-SiO₂ glasses was determined by first-order kinetics, and the activation energy equaled 95 kJ/mol. At 800°C, the maximum photoluminescence of the Sm²⁺ ions was achieved within 20 min.     

Association and physical gelation of ABA triblock copolymer in selective solvent

Association behavior and physical gelation mechanism of ABA triblock copolymer dissolved in B-selective solvent have been studied systematically from dilute to moderately concentrated solutions. Static and dynamic light scattering and nuclear magnetic resonance measurements for dilute solutions of poly(methyl methacrylate)-block-poly(tert-butyl acrylate)-block-poly(methyl methacrylate) (PMMA-PtBuA-PMMA) in 1-butanol (PtBuA selective solvent) indicated that PMMA-PtBuA-PMMA chains are molecularly dissolved above 50 °C. With decreasing temperature, the triblock copolymers form associated micelles consisting PMMA associated core and PtBuA shell. Linear dynamic viscoelastic measurements for solutions with moderate concentration (3.9-12.0 wt%) revealed that the system was viscous sol state at 60 °C. Drastic increase of shear storage modulus (G′) occurred with decreasing temperature, and at 25 °C, G′ showed rubbery plateau with weak frequency dependency, means the formation of elastic physical gel. The consistency between the temperature for micelle formation and that at the increase in G′ indicates that the physical gelation is owing to the network formation as the result of the association of PMMA chains and the bridging PtBuA chains connecting the PMMA cores. Master curves for the dynamic moduli were derived by time-temperature superposition along the frequency axis. Just above sol-gel transition concentration (C_gel), the master curves suggest the existence of fairy amount of aggregate that is not incorporated in the macroscopic network. With the increase in polymer concentration, the master curves become to reveal Maxwell-type viscoelasticity with narrow relaxation time distribution, suggesting the formation of transient network with easily generation and destruction of crosslinks. Concentration dependency of the plateau modulus is stronger than the theoretically expected, means the macroscopic transient network grows with polymer concentration by increasing the fraction of elastically effective bridging PtBuA chain above C_gel.     

The polymerization and copolymerization of nitroalkyl acrylates and nitroalkyl methacrylates

Nitroalkyl acrylates and methacrylates involving some new compounds were prepared. The homopolymerization of these monomers in toluene and their copolymerization with styrene in acetone were carried out with azobisisobutyronitrile as initiator. The rate of polymerization of the nitroalkyl acrylates showed a correlation with the number of nitro groups situated on the ester side chain. The apparent activation energies of the polymerization were found to be 22.0–27.5 kcal./mole for the nitroalkyl acrylates and about 11.5–13.0 kcal./mole for the nitroalkyl methacrylates. From the reactivity ratios and Q-e values of the copolymerization the following information was obtained. The copolymerization behavior of nitroalkyl acrylates and methacrylates showed an alternating tendency, and these monomers belong to the conjugative monomer groups. On the reactivities of these monomers, the polarity of vinyl group was affected a little by nitro group of ester bond side, and the resonance affected little. These monomers were crosslinked with 2-methyl-2-nitro-1,3-propylene diacrylate. Some of the polymers showed marked improvement in the physical properties of elastomers.     

Steam oxidation resistance of two-layered Ni-Cr and Al APS coating for USC boiler applications

Thermal spray of Ni-Cr and Al coatings was attempted on modified 9Cr-1Mo steel, to evaluate their steam oxidation resistance. Atmospheric plasma spray (APS) coatings of 50Ni-50Cr as undercoat and Al topcoat were attempted with the aim that the pores produced by 50Ni-50Cr undercoat can be filled with Al topcoat during the steam oxidation. The steam oxidized samples evinced the Ni and Cr diffusion towards the Al coating structure and changed the topcoat in to the Ni-Al intermetallics. Though the two-layered coating exhibited an excellent performance against the steam oxidation for the base steel substrate till 3000 h of test, the top layers of the coating underwent significant internal oxidation.     

Impedance-step phenomenon of thin-film GMI element with inclined magnetic stripe domain

An extraordinary impedance-step phenomenon of GMI (giant magnetoimpedance) effect was studied. It is observed for a thin-film GMI element with an inclined magnetic stripe domain. The “inclined stripe domain” means a domain structure that has inclined domain walls against the width direction of the GMI strip. An observation of magnetic domain reveals that a sudden change of domain structure, such as stripe-domain vanishing or occurrence, happens simultaneously with the impedance step. A theoretical consideration, based on the bias-susceptibility model of a single-domain magnetic thin film with uniaxial anisotropy, qualitatively shows that the existence of an inclined stripe domain makes the impedance lower than that characteristic of a single-domain structure.     

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded join     

RUNA: a multimodal command language for home robot users

This article describes a multimodal command language for home robot users, and a robot system which interprets users’ messages in the language through microphones, visual and tactile sensors, and control buttons. The command language comprises a set of grammar rules, a lexicon, and nonverbal events detected in hand gestures, readings of tactile sensors attached to the robots, and buttons on the controllers in the users’ hands. Prototype humanoid systems which immediately execute commands in the language are also presented, along with preliminary experiments of faceto-face interactions and teleoperations. Subjects unfamiliar with the language were able to command humanoids and complete their tasks with brief documents at hand, given a short demonstration beforehand. The command understanding system operating on PCs responded to multimodal commands without significant delay. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Detection of a brain aneurysm and a way to search for a brain aneurysm aimed at the development of a system to simulate an operation

In this article, a system is proposed for a simulated operation which would help a trainee surgeon to perform a medical operation to ensure that a cerebral aneurysm does not burst. The physician will have acquired empirical medical technologies from operations in traditional clinical teaching. However, there is a problem with safety and the burden to the patient. Therefore, recently a new training approach for a simulated medical operation using virtual reality has been explored. With the aim of developing a simulated system for a medical operation for a cerebral aneurysm, we considered the necessary functions such as detecting the brain aneurysm that is the target of the operation, and searching for a suitable blood vessel to make a plan for the operation.     

Construction of a robot control system which understands a voice and pointing actions

This research was aimed at making a robot that can go and get an object designated by the user. We produced a robot control system that uses pointing and voice control. This control system is composed of two systems. One system is the object instruction system that uses pointing, and the other is the object instruction system that uses voice. The approximate position of a designated object is recognized by the object instruction system that uses pointing, and information about the object and instructions about the operation are conveyed by the object instruction system that uses voice. This time, the object instruction system that uses pointing has been designed and verified as the first step. A calculation resource to calculate the approximate position of the designated object is obtained when the user points directly at the object. A robot can be moved around a designated object by using this system. The object instruction system that uses voice will be constructed in future work.