冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

驱蚊酯的合成及应用研究

本文合成了一种高效低毒驱蚊剂-驱蚊酯[(insectifuge ester)[1],3-(Acetyl-butyl-amino)-propionic acid ethyl ester],并对其结构进行了全面鉴定,同时对其合成过程中所产生的副产物进行了分析测定。用驱蚊酯配成含2.3%驱蚊酯的花露水,并测试了其驱蚊效果,有效驱蚊时间可达5小时以上。     

超临界CO2流体萃取莪术挥发油的工艺研究

利用超临界CO2流体萃取技术,以榄香烯为目标物,研究了萃取压力、温度、时间、原料粒度和CO2流量对莪术挥发油萃取率的影响,建立了获得莪术挥发油的最佳工艺条件.实验结果表明,莪术粉粒度40目,萃取压力18 MPa,温度50℃,萃取时间120 min,流量20～30 kg/h条件下,挥发油中榄香烯含量最高,相对含量为2.8%,为以后精馏研究奠定了基础.     

交联透明质酸的降解及其释药性能

用己二酸二酰肼（ADH）对透明质酸（HA）进行化学修饰，制备交联透明质酸（HA-ADH）薄膜。粘度法测试表明HA-ADH是一种可降解的生物材料，并且与HA相比，HA．ADH的降解速率减慢。在此基础上，研究了以疏水性的替硝唑（TDZ）和亲水性的头孢唑啉钠（CEZ）为模拟药物的HA-ADH药物载体薄膜的释药性能。紫外-可见（UV-Vis）吸收光谱检测表明，HA-ADH是一种疏水性药物TDZ的优良缓释制荆，这是由于TDZ的疏水性和HA-ADH薄膜的缓慢溶胀和降解性能的结合而得到的，药物的释放主要受扩散机制控制。     

公钥密码探源

如何能够在利用网络速度的同时,保护我们的信息安全,这给密码学家提出了一个难题。 公钥密码系统的诞生解决了这个难题。本文在研究了公钥密码学的教学基础上,以椭圆曲线加密 (ECC)为例,把椭圆曲线信息编码成二进制数,把明文加密成密文,把密文还原为明文,完整地研究 了公钥密码系统。     

Effect of boron on the low-cycle fatigue behavior and deformation structure of INCONEL 718 at 650 °C

Symmetrical push-pull low-cycle fatigue (LCF) tests were performed on INCONEL 718 (IN718) containing 12, 29, 60, and 100 ppm B at 650 °C. The results showed that all the alloys experienced a relatively short period of initial cyclic hardening at low strain amplitudes, followed by a regime of saturation or slightly continuous cyclic softening. The initial cyclic hardening phase decreased with increasing strain amplitudes, and disappeared at the high strain amplitudes. A serrated flow was observed in the plastic regions of cyclic stress-strain hysteresis loops. The saturated cyclic stress amplitude at a given strain amplitude was highest for the alloy with 60 ppm B, and lowest for the alloy with 12 ppm B. The LCF lifetime increased with increasing B concentration up to 60 ppm, and then decreased as the B content increased from 60 to 100 ppm. Fractographic analysis suggested that the fracture mode changed from intergranular to transgranular cracking as the B concentration increased. The characteristic deformation microstructures produced by LCF tests at 650 °C, examined via transmission electron microscopy, were regularly spaced arrays of planar deformation bands on {111} slip planes in all four alloys. A ladderlike structure was observed in some local regions in the alloy with 12 ppm B. Heavily deformed planar deformation bands were observed in the fatigued specimens with 100 ppm B. The mechanism of improvement in the LCF life of IN718 due to B addition is discussed.     

情境故事法在产品设计开发中的应用

从产品设计中"以使用者为中心"的设计要求出发,引入情境故事法的相关内容.详细论述了情境故事法的概念、流程、操作方法,并以商务笔记本为研究载体,对商务笔记本的典型用户的使用特性,以及使用过程中的最初情境和遇到的问题进行综合分析.站在用户的角度建立情境故事以寻求商务笔记本设计的创新点,从而得到新的故事方案.最后对情境故事法使用的局限性作了些简要评述.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

状如琼，凝为脂

在我们喝的饮料粒粒橙中，为什么那些细小的橙子颗粒是悬浮在橙汁中的呢？果冻和布丁为什么是透明，且柔软有弹性的呢？去看看成分表，我们不难发现共同之处，看似不同的食品都添加了一种共同的成分——琼脂。[编者按]