Stick-Breaking Dependent Beta Processes with Variational Inference

Neural Processing Letters - The beta processes (BP) is a powerful nonparametric tool in feature learning, which is often used as the prior of Bernoulli process for choosing features from a feature...     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

A method for rapidly evaluating reliability and predicting remaining useful life using two-dimensional convolutional neural network with signal conversion

Journal of Mechanical Science and Technology - Real-time monitoring and rapid evaluation of bearing operating conditions, especially for the reliability evaluation and remaining useful life (RUL)...     

复杂采空区充填开采对地面建筑的影响研究

矿山地下开采引起的围岩应力变化及地表变形影响着地面建筑物的安全。采用ABAQUS有限元软件对金属矿山充填开采引起的岩体变形及地表移动规律进行了研究。以矿山实际开采现状及实测数据为基础，建立了具有复杂空间结构的三维地层模型，利用子程序SIGINI编程施加地应力，采用修正Mohr-Coulomb模型模拟岩体，计算得出：由于围岩力学强度较高，开采引起顶板下沉量相对较小，充填对于控制底鼓具有一定抑制作用；预留矿柱主要承受较大竖向压应力，矿柱尺寸越小压缩量越大；地表充填站位于采空区边缘位置，水平及竖向位移相对较小，地表变形主要集中在采空区中部位置。研究成果可为矿山安全开采提供依据，为地面监测点的选择提供参考。     

Bamboo biochar-catalytic degradation of lignin under microwave heating

Abstract

Lignin biochar-catalytic depolymerization using biochar Fe-600, Fe-800, Ni-600, Ni-800 catalysts under microwave-heating (180?°C for 30?min) was explored in an ethanol/formic acid (1:1) media. Non-catalyst depolymerization was also studied and compared with the biochar-catalysts results. Characteristics of the bio-char catalysts were analyze by BET, XRD, and FT-IR. GPC, FT-IR, and MALDI-TOF MS spectrometry were also used to characterize the depolymerization products. The experimental results showed that the S_BET, V_t, and V_mec and average pore diameter of the biochars are considerably dependent on the preparation temperature and type of cation (Ni²⁺ or Fe³⁺). The maximum yield of bio-oil product was obtained as 85?wt% with the addition of biochar Ni-600 and the total amount of oligomers or monomers with a molecular weight of 164 to 446 reaches 80.4%.