Optoelectronic properties of graphene thin films prepared by thermal reduction of graphene oxide

Graphene thin films have been prepared by thermal reduction of graphene oxide. Raising the reduction temperature results in a red-shift of the G peak in Raman spectra. The reduction temperature turns out to strongly affect the morphology of the prepared graphene film. Photoluminescence (PL) results show that the band gap of graphene can be tuned by varying the reduction temperature. The thermal reduction process has been optimized in an effort to minimize the formation of wrinkles/folds on the graphene surface leading to enhanced PL and Raman peak intensities and reduced electrical sheet resistance.     

Preparation, testing and modeling of three-dimensionally ordered catalytic layers for electrocatalysis of fuel cell reactions

The arrays of vertically aligned carbon nano-filaments (VACNF) were synthesized by catalytic chemical vapor deposition on TiO_x substrates, obtained via oxidative treatment of polycrystalline Ti and Ti thin films on Si(1 0 0). VACNF were studied using scanning and transmission electron microscopies. The Pt deposition on VACNF was utilized to prepare a set of model catalysts, which were investigated in two fuel cell related reactions: the oxygen reduction (ORR) and the hydrogen oxidation (HOR) reactions. The experimental data were compared with the results of mathematical modeling performed for a fast (quasi)reversible and a slow irreversible electrochemical reaction. The approach made it possible to study electrochemical reactions (HOR, ORR) on nano-materials under well defined mass transport conditions. The influence of the catalytic layer thickness and the Pt coverage on the penetration depth of the reactive species inside the layer and consequently on the performance and on the Pt effectiveness factor were analyzed.     

Interfacial structural stabilization on amorphous silicon anode for improved cycling performance in lithium-ion batteries

Interfacial structures of electrode-current collector and electrode-electrolyte have been designed to be stabilized for improved cycling performance of amorphous silicon (Si) that is considered as an alternative anode material to graphite for lithium-ion batteries. Interfacial structural stabilization involves the interdigitation of Si electrode-Cu current collector substrate by anodic Cu etching with thiol-induced self-assembly, and the formation of self-assembled siloxane on the surface of Si electrode using silane. The novel interfacial architecture possesses promoted interfacial contact area between Si and Cu, and a surface protective layer of siloxane that suppresses interfacial reactions with the electrolyte of 1 M LiPF₆/ethylene carbonate (EC):diethylene carbondate (DEC). FTIR spectroscopic analyses revealed that a stable solid electrolyte interphase (SEI) layer composed of lithium carbonate, organic compounds with carboxylate metal salt and ester functionalities, and PF-containing species formed when having siloxane on Si electrode. Interfacially stabilized Si electrode exhibited a high capacity retention 80% of the maximum discharge capacity after 200 cycles between 0.1 and 1.5 V vs. Li/Li⁺. The data contribute to a basic understanding of interfacial structural causes responsible for the cycling performance of Si-based alloy anodes in lithium-ion batteries.     

Ammonia removal by sweep gas membrane distillation

Wastewater containing low levels of ammonia (100 mg/L) has been simulated in experiments with sweep gas membrane distillation at pH 11.5. The effects of feed temperature, gas flow rate and feed flow rate on ammonia removal, permeate flux and selectivity were investigated. The feed temperature is a crucial operating factor, with increasing feed temperature increasing the permeate flux significantly, but reducing the selectivity. The best-performing conditions of highest temperature and fastest gas flow rate resulted in 97% removal of the ammonia, to give a treated water containing only 3.3 mg/L of ammonia.     

A review of cardiac image registration methods

In this paper, the current status of cardiac image registration methods is reviewed. The combination of information from multiple cardiac image modalities, such as magnetic resonance imaging, computed tomography, positron emission tomography, single-photon emission computed tomography, and ultrasound, is of increasing interest in the medical community for physiologic understanding and diagnostic purposes. Registration of cardiac images is a more complex problem than brain image registration because the heart is a nonrigid moving organ inside a moving body. Moreover, as compared to the registration of brain images, the heart exhibits much fewer accurate anatomical landmarks. In a clinical context, physicians often mentally integrate image information from different modalities. Automatic registration, based on computer programs, might, however, offer better accuracy and repeatability and save time.     

Large‐Scale Noniridescent Structural Color Printing Enabled by Infiltration‐Driven Nonequilibrium Colloidal Assembly

Structural colors originating from interaction of light with intricately arranged micro‐/nanostructures have stimulated considerable interest because of their inherent photostability and energy efficiency. In particular, noniridescent structural color with wide viewing angle has been receiving increasing attention recently. However, no method is yet available for rapid and large‐scale fabrication of full‐spectrum structural color patterns with wide viewing angles. Here, infiltration‐driven nonequilibrium assembly of colloidal particles on liquid‐permeable and particle‐excluding substrates is demonstrated to direct the particles to form amorphous colloidal arrays (ACAs) within milliseconds. The infiltration‐assisted (IFAST) colloidal assembly opens new possibilities for rapid manufacture of noniridescent structural colors of ACAs and straightforward structural color mixing. Full‐spectrum noniridescent structural colors are successfully produced by mixing primary structural colors of red, blue, and yellow using a commercial office inkjet printer. Rapid fabrication of large‐scale structural color patterns with sophisticated color combination/layout by IFAST printing is realized. The IFAST technology is versatile for developing structural color patterns with wide viewing angles, as colloidal particles, inks, and substrates are flexibly designable for diverse applications.     

Characterizations of high resistivity TiNxOy thin films for applications in thin film resistors

We report about developing high resistivity thin film resistors using titanium oxy-nitride. Titanium nitride films of different thicknesses ranging from 50 to 300 nm were deposited on SiO₂/Si substrates using the reactive magnetron sputtering method. After deposition, these films were annealed in the air ambient. The structural and electrical properties of the films were examined as a function of annealing temperature. The samples with various thicknesses show TiN(1 1 1) phase. The sheet resistance increases from 150 up to 420 Ω/□ when the film thickness decreases from 300 to 50 nm. Temperature coefficience of resistance (TCR) of the films significantly decreased with decreasing the film thickness. The TCR of 50-nm thick film is quite low, about 49 ppm/K.