Novel aspects of wet milling for the production of microsuspensions and nanosuspensions of poorly water-soluble drugs

Micronization and nanoparticle production of poorly water-soluble drugs was investigated using single wet milling equipment operating in the attritor and stirred media modes. The drug particles in the median size range of 0.2?2??m were prepared by changing the milling mode and operating conditions of a Micros mill with a purpose of elucidating the dynamics of the wet milling process. It was determined that particle breakage due to mechanical stresses and aggregation due to insufficient stabilization are two competing mechanisms which together control the wet milling dynamics of the poorly water-soluble drugs. The study in the attritor mode using four different classes of stabilizers with six drugs indicated that steric stabilization worked better than electrostatic stabilization for the drugs studied. In addition, the existence of different minimum polymer concentrations for the stabilization of microsuspensions and nanosuspensions was indicated. The major role of a non-ionic polymer during the production of fine particles is its stabilization action through steric effects, and no experimental evidence was found to support the so-called Rehbinder effect. Periodic addition of the polymer as opposed to the addition of the polymer at the start of milling process was introduced as a novel processing method. This novel method of polymer addition provided effective stabilization and breakage of drug particles leading to a narrower and finer particle size distribution. Alternatively, it may allow shorter processing time and lower overall power consumption of the milling process for a desired particle size.     

Noninvasive estimation of dynamic pressures in vitro and in vivo using the subharmonic response from microbubbles

The purpose of this study was to develop and validate a noninvasive pressure estimation technique based on subharmonic emissions from a commercially available ultrasound contrast agent and scanner, unlike other studies that have either adopted a single-element transducer approach and/ or use of in-house contrast agents. Ambient pressures were varied in a closed-loop flow system between 0 and 120 mmHg and were recorded by a solid-state pressure catheter as the reference standard. Simultaneously, the ultrasound scanner was operated in pulse inversion mode transmitting at 2.5 MHz, and the unprocessed RF data were captured at different incident acoustic pressures (from 76 to 897 kPa). The subharmonic data for each pulse were extracted using band-pass filtering with averaging, and subsequently processed to eliminate noise. The incident acoustic pressure most sensitive to ambient pressure fluctuations was determined, and then the ambient pressure was tracked over 20 s. In vivo validation of this technique was performed in the left ventricle (LV) of 2 canines. In vitro, the subharmonic signal could track ambient pressure values with r(2) = 0.922 (p < 0.001), whereas in vivo, the subharmonic signal tracked the LV pressures with r(2) > 0.790 (p < 0.001) showing a maximum error of 2.84 mmHg compared with the reference standard. In conclusion, a subharmonic ultrasound-based pressure estimation technique, which can accurately track left ventricular pressures, has been established.     

Factors associated with food workers working while experiencing vomiting or diarrhea

This study sought to determine the frequency with which food workers said they had worked while experiencing vomiting or diarrhea, and to identify restaurant and worker characteristics associated with this behavior. We conducted interviews with food workers (n=491) and their managers (n=387) in the nine states that participate in the Centers for Disease Control and Prevention's Environmental Health Specialists Network. Restaurant and worker characteristics associated with repeatedly working while experiencing vomiting or diarrhea were analyzed via multivariable regression. Fifty-eight (11.9%) workers said they had worked while suffering vomiting or diarrhea on two or more shifts in the previous year. Factors associated with workers having worked while experiencing vomiting or diarrhea were (i) high volume of meals served, (ii) lack of policies requiring workers to report illness to managers, (iii) lack of on-call workers, (iv) lack of manager experience, and (v) workers of the male gender. Our findings suggest that policies that encourage workers to tell managers when they are ill and that help mitigate pressures to work while ill could reduce the number of food workers who work while experiencing vomiting or diarrhea.     

Stimuli-responsive releasing of gold nanoparticles and liposomes from aptamer-functionalized hydrogels

Controlled release of therapeutic agents is important for improving drug efficacy and reducing toxicity. Recently, hydrogels have been used for controlled release applications. While the majority of the previous work focused on releasing the cargo in response to physical stimuli such as temperature, light, electric field, and pH, we aim to trigger cargo release in the presence of small metabolites. In our system a DNA aptamer that can bind to adenosine, AMP, and ATP was used as a linker to attach either DNA-functionalized gold nanoparticles or liposomes to DNA-functionalized hydrogels. In the presence of the metabolite, both the nanoparticle and liposome cargos were released. The effect of salt, temperature, target concentration, and drying has been systematically studied. Interestingly, we found that the gel can be completely dried while retaining the DNA linkages and adenosine induced release was still achieved after rehydration. Our work demonstrates that aptamers can be used to control the release of drugs and other materials attached to hydrogels.     

Characterisation of acid mine drainage in a high rainfall mountain environment, New Zealand

The Stockton coal mine lies at 700-1100 m above sea level in a mountainous orographic precipitation zone on the West Coast of the South Island of New Zealand. Rainfall exceeds 6000 mm/year and arrives with frequent flood events that can deliver > 200 mm/day. Streams vary in discharges by up to two orders of magnitude over a time scale of hours. Pyritic waste rock at the mine interacts chemically with even the most intense rainfall, and almost all runoff is acidic to some degree. In the most intense rain event recorded in this study (> 10 mm/hour), dilution of acid mine drainage (AMD) occurred and pH rose from 3 to > 5 over several hours, with stream discharge at a monitoring point rising from < 0.5 to > 100 cumecs. However, most rain events of similar magnitude are less intense, longer duration, and only raise AMD pH to ~ 4 with similar high discharges. Results presented here for Stockton confirm that it is the intensity of rain events on the hourly scale, rather than the total amount of rainwater delivered to the site, that governs the amount and composition of AMD generated during flood events. Stream discharge loads of dissolved iron and aluminium range from ~ 20 to 1000 kg/hour. Dissolved sulfate and acidity loads are typically ~ 500 kg/hour but can exceed 20 tonnes/hour in rain events.First flush effects observable elsewhere around the world involving peak metal loads following dry periods or seasonal changes are not obvious at Stockton due to the high and variable rainfall environment. Dissolved Fe concentrations may be limited in runoff waters by precipitation of jarosite and schwertmannite, especially when rainfall is sufficiently intense to raise pH to 4 or higher. These minerals are widespread in the exposed waste rock on site. Likewise, precipitation of alunite may occur as pH rises in rain events, but no field evidence for this has been observed.     

Patterning of Epitaxial Perovskites from Micro and Nano Molded Stencil Masks

A process is developed that combines soft lithographic molding with pulsed laser deposition (PLD) to make heteroepitaxial patterns of functional perovskite oxide materials. Micro‐ and nanostructures of sacrificial ZnO are made by micro molding in capillaries (MiMiC) and nano transfer molding, respectively, and used to screen the single crystalline substrates during subsequent PLD. ZnO is used because of its compatibility with the high temperatures reached during PLD and because of the ease of its removal after use by benefiting from its amphoteric nature. Sub‐micrometer sized lines of La_0.67Sr_0.33MnO₃ are made by the transfer molding approach, preserving the anisotropic features expected for a fully oriented thin film and taking account for the magnetostatic contribution from the line shapes. Different patterns of SrRuO₃ are made with lateral dimensions of a few micrometers having individual features for which electrical isolation is illustrated. The bottom‐up soft lithographic methods can be compliantly utilized for making epitaxial structures of various shapes and sizes in the μm down to the nm range, and offer unique opportunities for fundamental studies as well as for realizing technological applications.     

Conjugated Polymers of Intrinsic Microporosity (C‐PIMs)

Conjugated microporous polymers (CMPs) have shown great potential for energy and environmental issues, however, poor solubility and processability of most of these materials limit their applications. Herein, a range of linear conjugated polymers of intrinsic microporosity (C‐PIMs) is reported, combining for the first time the properties of conjugated microporous polymers, such as tunable electronic properties and compositional variation, with those of linear polymers of intrinsic microporosity (PIMs) allowing for solution processability and film formation. These soluble materials have a number of potential applications, for example as components in devices where large, porous interfaces are combined with extended electronic conjugation.     

Design development and testing of a solar PV pump based drip system for orchards

A Solar Photovoltaic (PV) pump operated drip irrigation system has been designed and developed for growing orchards in arid region considering different design parameters like pumps size, water requirements, the diurnal variation in the pressure of the pump due to change in irradiance and pressure compensation in the drippers. The system comprising a PV pump with 900 W_p PV array and 800 W dc motor-pump mono-block, micro filter, main and sub-mains and three open-able low-pressure compensating drippers on each plant was field tested. The emission uniformity was observed to be 92–94% with discharge of 3.8 l/h in the pressure range of 70–100 kPa provided by the pump and thus the system could irrigate some 1 ha area within 2 h. Based on the performance of the PV pump and the drip system, it was inferred that about 5 ha area of orchard could be covered. The projected benefit–cost ratio for growing pomegranate orchards with such a system was evaluated to be above 2 even with the costly PV pump and therefore the system was considered to be an appropriate technology for the development of arid region.     

Commercialising aerospace composites

Dave Richard, Business Development Director for NCC, profiles Vector Composites Inc, a new US company launched to serve the aerospace industry.     

利用便携式示波器轻松进行浮动测量

泰克TPS2000系列示波器采用隔离通道（IsolatedChannel^TM）技术，提供厂四条隔离通道、全功能、电池操作的示波器。该仪器提供厂高达200MHz的带宽和2GS／s的实时取样速率，一个隔离外部触发器和8小时连续电池操作能力，TPS2000系列示波器用途广泛。使得工程师和技术人员能够在实验室或现场迅速、精确、经济地进行浮动测量和差分测量。