Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

水资源承载力分析研究

水是人们生存必不可少的资源,是生产与生活的基础,但水资源短缺,时间、空间分布不均,利用率低,已成为制约各地经济可持续发展的重要因素之一。本文所选研究区域——昌宁县正处于经济快速发展时期,水资源承载力将会影响其发展,文章综合文献分析和实际调研数据,运用科学的方法进行水资源的承载力分析,结果表明:昌宁县水资源承载力目前与社会经济的发展相适应,但远期将会有所不足,因而要求协调人与自然的矛盾,促进昌宁县的可持续发展。     

Extending SSD Lifespan with Comprehensive Non-Volatile Memory-Based Write Buffers

Journal of Computer Science and Technology - New non-volatile memory (NVM) technologies are expected to replace main memory DRAM (dynamic random access memory) in the near future. NAND flash...     

高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。     

A computer aided design method for car form and its application based on shape parameters

In the early design stage, automotive modeling should both meet the requirements of aesthetics and engineering. Therefore, a vehicle CAD (computer aided design) model that can be easily adjusted by feedbacks is necessary. Based on CE-Bézier surface, this paper presents a set of algorithms for parametric segmentation and fairing surface generation in a car model. This model is defined by a simplified automotive template and relevant control points, shape parameters and segmentation parameters, which can be modified to alter the car form efficiently. With this model and the corresponding adjustment method, more than fifty various vehicle models are established in this research according to different parameters. And two methods for calculating similarity index between car models are constructed, which are suitable for brand design trend analysis and modelling design decisionmaking.     

Study on the Height of the Mining-Induced Water-Conducting Fracture Zone Under the Q 2l Loess Cover of the Jurassic Coal Seam in Northern Shaanxi,China

A method to calculate the height of a water-conducting fractured zone (HWCFZ) was developed based on the plate and shell theory, and the development of the HWCFZ in bedrock and Q2l loess strata is discussed in detail. First, the subsidence-deflection curve equation of the overlying stratum is theoretically derived, and then the ultimate deflection and free space height of rock strata are calculated. Moreover, the strata tensile strain is calculated by using integral calculus. In addition, the failure state of the rock is analyzed by comparing the theoretically calculated tensile strain with the experimentally measured yield tensile strain, allowing one to attain the maximum value of HWCFZ. This approach was tested at the Jinjitan coal mine; the theoretically predicted, experimentally measured, and numerically computed maximum HWCFZ values were 189.5, 187.3, and 188.5 m, respectively, demonstrating the accuracy of the proposed method. These results are highly significant for safe and environment-friendly coal mining in northwest Shaanxi, China.     

古建筑木结构透榫节点力学模型研究

为研究古建筑木结构透榫节点的M-θ力学模型，在分析透榫节点构造特征与受力机理的基础上，建立其数值模型，用透榫节点的试验数据验证了该数值模型的正确性，并分析了节点缝隙、木材横纹弹性模量和大榫头长度对透榫节点受弯承载力的影响。根据受力分析结果，建立以弹性点、屈服点与极限点为特征点的三折线多参数M-θ力学模型，其结果与多数的试验结果基本吻合，并将该力学模型应用于木构架的受力分析。研究结果表明：透榫节点的滞回耗能能力强，节点的变形主要集中在榫头处。当榫头与卯口之间的缝隙增大时，节点的受弯承载力降低。随木材横纹弹性模量的提高和大榫头长度的增加，节点的受弯承载力有一定提高。文章建立的M-θ力学模型能较好反映透榫节点的受力过程，适用于木构架的受力分析，其荷载 位移骨架曲线与试验结果基本吻合。研究成果可为古建筑木结构的维修与保护提供参考。     

Mechanophysical Cues in Extracellular Matrix Regulation of Cell Behavior

The extracellular matrix (ECM) is a macromolecular network that can provide biochemical and structural support for cell adhesion and formation. It regulates cell behavior by influencing biochemical and physical cues. It is a dynamic structure whose components are modified, degraded, or deposited during connective tissue development, giving tissues strength and structural integrity. The physical properties of the natural ECM environment control the design of naturally or synthetically derived biomaterials to guide cell function in tissue engineering. Tissue engineering is an important field that explores physical cues of the ECM to produce new viable tissue for medical applications, such as in organ transplant and organ recovery. Understanding how the ECM exerts physical effects on cell behavior, when cells are seeded in synthetic ECM scaffolds, is of utmost importance. Herein we review recent findings in this area that report on cell behaviors in a variety of ECMs with different physical properties, i.e., topology, geometry, dimensionality, stiffness, and tension.