7075铝合金热变形连接接头的组织与性能

应用Gleeble-3500热模拟机对7075铝合金进行了热变形连接试验,利用金相显微镜和扫描电镜对不同温度和保温时间的接头界面组织进行了观察和分析,并对接头进行了拉伸性能测试。结果表明:当连接温度为460 ℃,保温时间为24 h时,对界面进行EDS分析,界面处已经没有氧化物的偏聚,此时的力学性能最佳,抗拉强度达到444 MPa,屈服强度为265 MPa。     

CFD Modeling of Active Volume Creation in a Non‐Newtonian Fluid Agitated by Submerged Recirculating Jets

Computational fluid dynamics (CFD) models were employed to investigate flow conditions inside a model reactor in which yield stress non‐Newtonian liquid is mobilized using submerged recirculating jets. The simulation results agree well with the experimental results of active volume in the reactor obtained using flow visualization by the authors in a previous study. The models developed are capable of predicting a critical jet velocity (v_c) that determines the extent of active volume obtained due to jet mixing. The v_c values are influenced both by the rheological properties of the liquid and the nozzle orientation. The liquid with higher effective viscosity leads to higher v_c for a downward facing injection nozzle. However, an upward facing injection nozzle along with a downward facing suction nozzle generates enhanced complementary flow fields which overcome the rheological constraints of the liquid and lead to lower v_c.     

Fulde–Ferrell State in Spin–Orbit-Coupled Superconductor: Application to Dresselhaus SOC

We show that in the presence of magnetic field, two superconducting phases with the center-of-mass momentum of Cooper pair parallel to the magnetic field are induced in Dresselhaus spin–orbit-coupled superconductor. Specifically, at small magnetic field, the center-of-mass momentum is induced due to the energy-spectrum distortion and no unpairing region with vanishing singlet correlation appears. We refer to this superconducting state as the drift-BCS state. By further increasing the magnetic field, the superconducting state falls into the Fulde–Ferrell state with the emergence of the unpairing regions. The observed abrupt enhancement of the center-of-mass momenta and suppression on the order parameters during the transition indicate the occurrence of a first-order phase transition. Enhanced Pauli limit and hence enlarged magnetic-field regime of the Fulde–Ferrell state, due to the spin-flip terms of the spin–orbit coupling, are revealed. We also address the triplet correlations induced by the spin–orbit coupling, and show that the Cooper-pair spin polarizations, generated by the magnetic field and center-of-mass momentum with the triplet correlations exhibit totally different magnetic-field dependences between the drift-BCS and Fulde–Ferrell states.     

Adaptive Finite-time Tracking Control for Class of Uncertain Nonlinearly Parameterized Systems with Input Delay

International Journal of Control, Automation and Systems - In this paper, the tracking problem for a class of uncertain nonlinearly parameterized systems with input delay based the adaptive...     

极薄、超宽规格装甲板压力淬火工艺数值模拟优化

利用数值模拟的方法对极薄、超宽规格装甲板淬火过程的畸变进行了模拟研究,并对脉冲式压力淬火的控制参数进行了优化。通过对比不同冷却条件装甲板的变形量,确定了脉冲式压力淬火的脉冲压力和周期。结果表明,脉冲约束的模拟条件下,装甲板在厚度Z方向上的最终变形量为1.7 mm,不仅小于2 mm的标准要求,而且可以实现装甲板的小淬火畸变前提下满足其表面无压痕、划痕等其他损伤的实际生产需求。     

Effects of CMC and Micelle Formation on the Removal of Sodium Benzoate or Sodium Stearate in a Sodium Aluminate Solution

JOM - Micelle formation over a critical micelle concentration (CMC) is related to the economic removal of organics in a sodium aluminate solution. In this research, removal of organics was...     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.